diff --git a/core/linux-rpi/PKGBUILD b/core/linux-rpi/PKGBUILD
index 1b3a16388..4aec5d7c9 100644
--- a/core/linux-rpi/PKGBUILD
+++ b/core/linux-rpi/PKGBUILD
@@ -10,7 +10,7 @@ _srcname=linux-${_commit}
 _kernelname=${pkgbase#linux}
 _regen=
 pkgver=6.1.65
-pkgrel=2
+pkgrel=3
 pkgdesc='Linux'
 url="http://www.kernel.org/"
 arch=(armv7h aarch64)
@@ -39,7 +39,7 @@ md5sums=('bb61562a9944c3e825eced2972f1b32b'
          '441ec084c47cddc53e592fb0cbce4edf'
          'c8f84694321e249492c80149833671d7')
 md5sums_armv7h=('2a063e35699f7e0b05f5d92edf230e36'
-                'a99311daa39248cfc9b6541a0a0a5f09')
+                '0302342da3d17130476a456c171d3594')
 md5sums_aarch64=('a4910e70559723ca477bd2e52164ba8d'
                  '7e4403dea857e40005bf76beda9927ff')
 
diff --git a/core/linux-rpi/config.txt b/core/linux-rpi/config.txt
index 1e6d64032..cf9f2b6dc 100644
--- a/core/linux-rpi/config.txt
+++ b/core/linux-rpi/config.txt
@@ -1,11 +1,26 @@
-# See /boot/overlays/README for all available options
+# For more options and information see:
+# http://rptl.io/configtxt
 
-dtoverlay=vc4-kms-v3d
 initramfs initramfs-linux.img followkernel
 
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Additional overlays and parameters are documented
+# /boot/firmware/overlays/README
+
+# Automatically load overlays for detected cameras
+camera_auto_detect=1
+
 # Automatically load overlays for detected DSI displays
 display_auto_detect=1
 
+# Enable DRM VC4 V3D driver
+dtoverlay=vc4-kms-v3d
+max_framebuffers=2
+
 # Uncomment if hdmi display is not detected and composite is being output
 #hdmi_force_hotplug=1
 
@@ -13,17 +28,12 @@ display_auto_detect=1
 #dtoverlay=disable-wifi
 #dtoverlay=disable-bt
 
-# Uncomment some or all of these to enable the optional hardware interfaces
-#dtparam=i2c_arm=on
-#dtparam=i2s=on
-#dtparam=spi=on
-
 # Uncomment this to enable infrared communication.
 #dtoverlay=gpio-ir,gpio_pin=17
 #dtoverlay=gpio-ir-tx,gpio_pin=18
 
-# Automatically load overlays for detected cameras
-camera_auto_detect=1
+# Run as fast as firmware / board allows
+arm_boost=1
 
 [cm4]
 # Enable host mode on the 2711 built-in XHCI USB controller.
@@ -31,6 +41,4 @@ camera_auto_detect=1
 # (e.g. for USB device mode) or if USB support is not required.
 otg_mode=1
 
-[pi4]
-# Run as fast as firmware / board allows
-arm_boost=1
+[all]