diff -ruN a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts --- a/arch/arm/boot/dts/kirkwood-goflexnet.dts 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts 1969-12-31 19:00:00.000000000 -0500 @@ -1,99 +0,0 @@ -/dts-v1/; - -/include/ "kirkwood.dtsi" - -/ { - model = "Seagate GoFlex Net"; - compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; - }; - - ocp@f1000000 { - serial@12000 { - clock-frequency = <200000000>; - status = "ok"; - }; - - nand@3000000 { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "pogoplug"; - reg = <0x0500000 0x2000000>; - }; - - partition@2500000 { - label = "root"; - reg = <0x02500000 0xd800000>; - }; - }; - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - - }; - gpio-leds { - compatible = "gpio-leds"; - - health { - label = "status:green:health"; - gpios = <&gpio1 14 1>; - linux,default-trigger = "default-on"; - }; - fault { - label = "status:orange:fault"; - gpios = <&gpio1 15 1>; - }; - left0 { - label = "status:white:left0"; - gpios = <&gpio1 10 0>; - }; - left1 { - label = "status:white:left1"; - gpios = <&gpio1 11 0>; - }; - left2 { - label = "status:white:left2"; - gpios = <&gpio1 12 0>; - }; - left3 { - label = "status:white:left3"; - gpios = <&gpio1 13 0>; - }; - right0 { - label = "status:white:right0"; - gpios = <&gpio1 6 0>; - }; - right1 { - label = "status:white:right1"; - gpios = <&gpio1 7 0>; - }; - right2 { - label = "status:white:right2"; - gpios = <&gpio1 8 0>; - }; - right3 { - label = "status:white:right3"; - gpios = <&gpio1 9 0>; - }; - }; -}; diff -ruN a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts --- a/arch/arm/boot/dts/kirkwood-iconnect.dts 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/boot/dts/kirkwood-iconnect.dts 1969-12-31 19:00:00.000000000 -0500 @@ -1,72 +0,0 @@ -/dts-v1/; - -/include/ "kirkwood.dtsi" - -/ { - model = "Iomega Iconnect"; - compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)"; - linux,initrd-start = <0x4500040>; - linux,initrd-end = <0x4800000>; - }; - - ocp@f1000000 { - i2c@11000 { - status = "okay"; - - lm63: lm63@4c { - compatible = "national,lm63"; - reg = <0x4c>; - }; - }; - serial@12000 { - clock-frequency = <200000000>; - status = "ok"; - }; - }; - gpio-leds { - compatible = "gpio-leds"; - - led-level { - label = "led_level"; - gpios = <&gpio1 9 0>; - linux,default-trigger = "default-on"; - }; - power-blue { - label = "power:blue"; - gpios = <&gpio1 10 0>; - linux,default-trigger = "timer"; - }; - power-red { - label = "power:red"; - gpios = <&gpio1 11 0>; - }; - usb1 { - label = "usb1:blue"; - gpios = <&gpio1 12 0>; - }; - usb2 { - label = "usb2:blue"; - gpios = <&gpio1 13 0>; - }; - usb3 { - label = "usb3:blue"; - gpios = <&gpio1 14 0>; - }; - usb4 { - label = "usb4:blue"; - gpios = <&gpio1 15 0>; - }; - otb { - label = "otb:blue"; - gpios = <&gpio1 16 0>; - }; - }; -}; diff -ruN a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/kirkwood-ts219-6281.dts --- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/boot/dts/kirkwood-ts219-6281.dts 1969-12-31 19:00:00.000000000 -0500 @@ -1,21 +0,0 @@ -/dts-v1/; - -/include/ "kirkwood-ts219.dtsi" - -/ { - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@1 { - label = "USB Copy"; - linux,code = <133>; - gpios = <&gpio0 15 1>; - }; - button@2 { - label = "Reset"; - linux,code = <0x198>; - gpios = <&gpio0 16 1>; - }; - }; -}; \ No newline at end of file diff -ruN a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts --- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts 1969-12-31 19:00:00.000000000 -0500 @@ -1,21 +0,0 @@ -/dts-v1/; - -/include/ "kirkwood-ts219.dtsi" - -/ { - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@1 { - label = "USB Copy"; - linux,code = <133>; - gpios = <&gpio1 11 1>; - }; - button@2 { - label = "Reset"; - linux,code = <0x198>; - gpios = <&gpio1 5 1>; - }; - }; -}; \ No newline at end of file diff -ruN a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/kirkwood-ts219.dtsi --- a/arch/arm/boot/dts/kirkwood-ts219.dtsi 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/boot/dts/kirkwood-ts219.dtsi 1969-12-31 19:00:00.000000000 -0500 @@ -1,78 +0,0 @@ -/include/ "kirkwood.dtsi" - -/ { - model = "QNAP TS219 family"; - compatible = "qnap,ts219", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - - ocp@f1000000 { - i2c@11000 { - status = "okay"; - clock-frequency = <400000>; - - s35390a: s35390a@30 { - compatible = "s35390a"; - reg = <0x30>; - }; - }; - serial@12000 { - clock-frequency = <200000000>; - status = "okay"; - }; - serial@12100 { - clock-frequency = <200000000>; - status = "okay"; - }; - spi@10600 { - status = "okay"; - - m25p128@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "m25p128"; - reg = <0>; - spi-max-frequency = <20000000>; - mode = <0>; - - partition@0000000 { - reg = <0x00000000 0x00080000>; - label = "U-Boot"; - }; - - partition@00200000 { - reg = <0x00200000 0x00200000>; - label = "Kernel"; - }; - - partition@00400000 { - reg = <0x00400000 0x00900000>; - label = "RootFS1"; - }; - partition@00d00000 { - reg = <0x00d00000 0x00300000>; - label = "RootFS2"; - }; - partition@00040000 { - reg = <0x00080000 0x00040000>; - label = "U-Boot Config"; - }; - partition@000c0000 { - reg = <0x000c0000 0x00140000>; - label = "NAS Config"; - }; - }; - }; - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - }; -}; diff -ruN a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c --- a/arch/arm/mach-kirkwood/board-goflexnet.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/board-goflexnet.c 1969-12-31 19:00:00.000000000 -0500 @@ -1,71 +0,0 @@ -/* - * Copyright 2012 (C), Jason Cooper - * - * arch/arm/mach-kirkwood/board-goflexnet.c - * - * Seagate GoFlext Net Board Init for drivers not converted to - * flattened device tree yet. - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Copied and modified for Seagate GoFlex Net support by - * Joshua Coombs based on ArchLinux ARM's - * GoFlex kernel patches. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "common.h" -#include "mpp.h" - -static struct mv643xx_eth_platform_data goflexnet_ge00_data = { - .phy_addr = MV643XX_ETH_PHY_ADDR(0), -}; - -static unsigned int goflexnet_mpp_config[] __initdata = { - MPP29_GPIO, /* USB Power Enable */ - MPP47_GPIO, /* LED Orange */ - MPP46_GPIO, /* LED Green */ - MPP45_GPIO, /* LED Left Capacity 3 */ - MPP44_GPIO, /* LED Left Capacity 2 */ - MPP43_GPIO, /* LED Left Capacity 1 */ - MPP42_GPIO, /* LED Left Capacity 0 */ - MPP41_GPIO, /* LED Right Capacity 3 */ - MPP40_GPIO, /* LED Right Capacity 2 */ - MPP39_GPIO, /* LED Right Capacity 1 */ - MPP38_GPIO, /* LED Right Capacity 0 */ - 0 -}; - -void __init goflexnet_init(void) -{ - /* - * Basic setup. Needs to be called early. - */ - kirkwood_mpp_conf(goflexnet_mpp_config); - - if (gpio_request(29, "USB Power Enable") != 0 || - gpio_direction_output(29, 1) != 0) - pr_err("can't setup GPIO 29 (USB Power Enable)\n"); - kirkwood_ehci_init(); - - kirkwood_ge00_init(&goflexnet_ge00_data); -} diff -ruN a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c --- a/arch/arm/mach-kirkwood/board-iconnect.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/board-iconnect.c 1969-12-31 19:00:00.000000000 -0500 @@ -1,106 +0,0 @@ -/* - * arch/arm/mach-kirkwood/board-iconnect.c - * - * Iomega i-connect Board Setup - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "common.h" -#include "mpp.h" - -static struct mv643xx_eth_platform_data iconnect_ge00_data = { - .phy_addr = MV643XX_ETH_PHY_ADDR(11), -}; - -static unsigned int iconnect_mpp_config[] __initdata = { - MPP12_GPIO, - MPP35_GPIO, - MPP41_GPIO, - MPP42_GPIO, - MPP43_GPIO, - MPP44_GPIO, - MPP45_GPIO, - MPP46_GPIO, - MPP47_GPIO, - MPP48_GPIO, - 0 -}; - -static struct mtd_partition iconnect_nand_parts[] = { - { - .name = "flash", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -/* yikes... theses are the original input buttons */ -/* but I'm not convinced by the sw event choices */ -static struct gpio_keys_button iconnect_buttons[] = { - { - .type = EV_SW, - .code = SW_LID, - .gpio = 12, - .desc = "Reset Button", - .active_low = 1, - .debounce_interval = 100, - }, { - .type = EV_SW, - .code = SW_TABLET_MODE, - .gpio = 35, - .desc = "OTB Button", - .active_low = 1, - .debounce_interval = 100, - }, -}; - -static struct gpio_keys_platform_data iconnect_button_data = { - .buttons = iconnect_buttons, - .nbuttons = ARRAY_SIZE(iconnect_buttons), -}; - -static struct platform_device iconnect_button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &iconnect_button_data, - }, -}; - -void __init iconnect_init(void) -{ - kirkwood_mpp_conf(iconnect_mpp_config); - kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25); - - kirkwood_ehci_init(); - kirkwood_ge00_init(&iconnect_ge00_data); - - platform_device_register(&iconnect_button_device); -} - -static int __init iconnect_pci_init(void) -{ - if (of_machine_is_compatible("iom,iconnect")) - kirkwood_pcie_init(KW_PCIE0); - return 0; -} -subsys_initcall(iconnect_pci_init); diff -ruN a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c --- a/arch/arm/mach-kirkwood/board-ts219.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/board-ts219.c 1969-12-31 19:00:00.000000000 -0500 @@ -1,82 +0,0 @@ -/* - * - * QNAP TS-11x/TS-21x Turbo NAS Board Setup via DT - * - * Copyright (C) 2012 Andrew Lunn - * - * Based on the board file ts219-setup.c: - * - * Copyright (C) 2009 Martin Michlmayr - * Copyright (C) 2008 Byron Bradley - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "common.h" -#include "mpp.h" -#include "tsx1x-common.h" - -static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = { - .phy_addr = MV643XX_ETH_PHY_ADDR(8), -}; - -static unsigned int qnap_ts219_mpp_config[] __initdata = { - MPP0_SPI_SCn, - MPP1_SPI_MOSI, - MPP2_SPI_SCK, - MPP3_SPI_MISO, - MPP4_SATA1_ACTn, - MPP5_SATA0_ACTn, - MPP8_TW0_SDA, - MPP9_TW0_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP13_UART1_TXD, /* PIC controller */ - MPP14_UART1_RXD, /* PIC controller */ - MPP15_GPIO, /* USB Copy button (on devices with 88F6281) */ - MPP16_GPIO, /* Reset button (on devices with 88F6281) */ - MPP36_GPIO, /* RAM: 0: 256 MB, 1: 512 MB */ - MPP37_GPIO, /* Reset button (on devices with 88F6282) */ - MPP43_GPIO, /* USB Copy button (on devices with 88F6282) */ - MPP44_GPIO, /* Board ID: 0: TS-11x, 1: TS-21x */ - 0 -}; - -void __init qnap_dt_ts219_init(void) -{ - u32 dev, rev; - - kirkwood_mpp_conf(qnap_ts219_mpp_config); - - kirkwood_pcie_id(&dev, &rev); - if (dev == MV88F6282_DEV_ID) - qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0); - - kirkwood_ge00_init(&qnap_ts219_ge00_data); - kirkwood_ehci_init(); - - pm_power_off = qnap_tsx1x_power_off; -} - -/* FIXME: Will not work with DT. Maybe use MPP40_GPIO? */ -static int __init ts219_pci_init(void) -{ - if (machine_is_ts219()) - kirkwood_pcie_init(KW_PCIE0); - - return 0; -} -subsys_initcall(ts219_pci_init); diff -ruN a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h --- a/arch/arm/mach-kirkwood/common.h 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/common.h 2012-10-10 15:03:29.000000000 -0400 @@ -58,11 +58,6 @@ #else static inline void dreamplug_init(void) {}; #endif -#ifdef CONFIG_MACH_TS219_DT -void qnap_dt_ts219_init(void); -#else -static inline void qnap_dt_ts219_init(void) {}; -#endif #ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT void dnskw_init(void); @@ -70,24 +65,12 @@ static inline void dnskw_init(void) {}; #endif -#ifdef CONFIG_MACH_ICONNECT_DT -void iconnect_init(void); -#else -static inline void iconnect_init(void) {}; -#endif - #ifdef CONFIG_MACH_IB62X0_DT void ib62x0_init(void); #else static inline void ib62x0_init(void) {}; #endif -#ifdef CONFIG_MACH_GOFLEXNET_DT -void goflexnet_init(void); -#else -static inline void goflexnet_init(void) {}; -#endif - #ifdef CONFIG_MACH_LSXL_DT void lsxl_init(void); #else diff -ruN a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c --- a/arch/arm/mach-kirkwood/dockstar-setup.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/dockstar-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -29,6 +29,10 @@ .offset = 0, .size = SZ_1M }, { + .name = "pogoplug", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_32M + }, { .name = "uImage", .offset = MTDPART_OFS_NXTBLK, .size = SZ_4M @@ -45,17 +49,17 @@ static struct gpio_led dockstar_led_pins[] = { { - .name = "dockstar:green:health", + .name = "status:green:health", .default_trigger = "default-on", .gpio = 46, .active_low = 1, }, { - .name = "dockstar:orange:misc", + .name = "status:orange:fault", .default_trigger = "none", .gpio = 47, .active_low = 1, - }, + } }; static struct gpio_led_platform_data dockstar_led_data = { @@ -73,8 +77,8 @@ static unsigned int dockstar_mpp_config[] __initdata = { MPP29_GPIO, /* USB Power Enable */ - MPP46_GPIO, /* LED green */ - MPP47_GPIO, /* LED orange */ + MPP46_GPIO, /* LED Green */ + MPP47_GPIO, /* LED Orange */ 0 }; diff -ruN a/arch/arm/mach-kirkwood/goflexhome-setup.c b/arch/arm/mach-kirkwood/goflexhome-setup.c --- a/arch/arm/mach-kirkwood/goflexhome-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/goflexhome-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,124 @@ +/* + * arch/arm/mach-kirkwood/goflexhome-setup.c + * + * Seagate GoFlex Home Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition goflexhome_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_2M + SZ_4M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data goflexhome_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data goflexhome_sata_data = { + .n_ports = 1, +}; + +static struct gpio_led goflexhome_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 46, + .active_low = 1, + }, + { + .name = "status:orange:fault", + .default_trigger = "none", + .gpio = 47, + .active_low = 1, + }, + { + .name = "status:white:misc", + .default_trigger = "none", + .gpio = 40, + .active_low = 0, + } +}; + +static struct gpio_led_platform_data goflexhome_led_data = { + .leds = goflexhome_led_pins, + .num_leds = ARRAY_SIZE(goflexhome_led_pins), +}; + +static struct platform_device goflexhome_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &goflexhome_led_data, + } +}; + +static unsigned int goflexhome_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP47_GPIO, /* LED Orange */ + MPP46_GPIO, /* LED Green */ + MPP40_GPIO, /* LED White */ + 0 +}; + +static void __init goflexhome_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(goflexhome_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(goflexhome_nand_parts), 40); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + kirkwood_ge00_init(&goflexhome_ge00_data); + kirkwood_sata_init(&goflexhome_sata_data); + + platform_device_register(&goflexhome_leds); +} + +MACHINE_START(GOFLEXHOME, "Seagate GoFlex Home") + /* Maintainer: Peter Carmichael */ + .atag_offset = 0x100, + .init_machine = goflexhome_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END + diff -ruN a/arch/arm/mach-kirkwood/goflexnet-setup.c b/arch/arm/mach-kirkwood/goflexnet-setup.c --- a/arch/arm/mach-kirkwood/goflexnet-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/goflexnet-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,177 @@ +/* + * arch/arm/mach-kirkwood/goflexnet-setup.c + * + * Seagate GoFlex Net Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition goflexnet_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { + .name = "pogoplug", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_32M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data goflexnet_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data goflexnet_sata_data = { + .n_ports = 2, +}; + +static struct gpio_led goflexnet_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 46, // 0x4000 + .active_low = 1, + }, + { + .name = "status:orange:fault", + .default_trigger = "none", + .gpio = 47, // 0x8000 + .active_low = 1, + }, + { + .name = "status:white:left0", + .default_trigger = "none", + .gpio = 42, // 0x0400 + .active_low = 0, + }, + { + .name = "status:white:left1", + .default_trigger = "none", + .gpio = 43, // 0x0800 + .active_low = 0, + }, + { + .name = "status:white:left2", + .default_trigger = "none", + .gpio = 44, // 0x1000 + .active_low = 0, + }, + { + .name = "status:white:left3", + .default_trigger = "none", + .gpio = 45, // 0x2000 + .active_low = 0, + }, + { + .name = "status:white:right0", + .default_trigger = "none", + .gpio = 38, // 0x0040 + .active_low = 0, + }, + { + .name = "status:white:right1", + .default_trigger = "none", + .gpio = 39, // 0x0080 + .active_low = 0, + }, + { + .name = "status:white:right2", + .default_trigger = "none", + .gpio = 40, // 0x0100 + .active_low = 0, + }, + { + .name = "status:white:right3", + .default_trigger = "none", + .gpio = 41, // 0x0200 + .active_low = 0, + } +}; + +static struct gpio_led_platform_data goflexnet_led_data = { + .leds = goflexnet_led_pins, + .num_leds = ARRAY_SIZE(goflexnet_led_pins), +}; + +static struct platform_device goflexnet_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &goflexnet_led_data, + } +}; + +static unsigned int goflexnet_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP47_GPIO, /* LED Orange */ + MPP46_GPIO, /* LED Green */ + MPP45_GPIO, /* LED Left Capacity 3 */ + MPP44_GPIO, /* LED Left Capacity 2 */ + MPP43_GPIO, /* LED Left Capacity 1 */ + MPP42_GPIO, /* LED Left Capacity 0 */ + MPP41_GPIO, /* LED Right Capacity 3 */ + MPP40_GPIO, /* LED Right Capacity 2 */ + MPP39_GPIO, /* LED Right Capacity 1 */ + MPP38_GPIO, /* LED Right Capacity 0 */ + 0 +}; + +static void __init goflexnet_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(goflexnet_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(goflexnet_nand_parts), 40); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + kirkwood_ge00_init(&goflexnet_ge00_data); + kirkwood_sata_init(&goflexnet_sata_data); + + platform_device_register(&goflexnet_leds); +} + +MACHINE_START(GOFLEXNET, "Seagate GoFlex Net") + /* Maintainer: Peter Carmichael */ + .atag_offset = 0x100, + .init_machine = goflexnet_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END + diff -ruN a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c --- a/arch/arm/mach-kirkwood/guruplug-setup.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/guruplug-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -57,22 +57,24 @@ static struct gpio_led guruplug_led_pins[] = { { - .name = "guruplug:red:health", + .name = "status:red:fault", + .default_trigger = "none", .gpio = 46, .active_low = 1, }, { - .name = "guruplug:green:health", + .name = "status:green:health", + .default_trigger = "default-on", .gpio = 47, .active_low = 1, }, { - .name = "guruplug:red:wmode", + .name = "status:red:wmode", .gpio = 48, .active_low = 1, }, { - .name = "guruplug:green:wmode", + .name = "status:green:wmode", .gpio = 49, .active_low = 1, }, diff -ruN a/arch/arm/mach-kirkwood/iconnect-setup.c b/arch/arm/mach-kirkwood/iconnect-setup.c --- a/arch/arm/mach-kirkwood/iconnect-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/iconnect-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,204 @@ +/* + * arch/arm/mach-kirkwood/iconnect-setup.c + * + * Iomega iConnect Wireless + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition iconnect_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_1M + SZ_2M + }, { + .name = "rootfs", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_32M, + }, { + .name = "data", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data iconnect_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(11), +}; + +static struct gpio_led iconnect_led_pins[] = { + { + .name = "iconnect:led_level", + .default_trigger = "default-on", + .gpio = 41, + }, + { + .name = "iconnect:blue:power", + .default_trigger = "default-on", + .gpio = 42, + }, + { + .name = "iconnect:red:power", + .gpio = 43, + }, + { + .name = "iconnect:blue:usb1", + .gpio = 44, + }, + { + .name = "iconnect:blue:usb2", + .gpio = 45, + }, + { + .name = "iconnect:blue:usb3", + .gpio = 46, + }, + { + .name = "iconnect:blue:usb4", + .gpio = 47, + }, + { + .name = "iconnect:blue:otb", + .gpio = 48, + }, +}; + +static struct gpio_led_platform_data iconnect_led_data = { + .leds = iconnect_led_pins, + .num_leds = ARRAY_SIZE(iconnect_led_pins), +}; + +static struct platform_device iconnect_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &iconnect_led_data, + } +}; + +#define ICONNECT_GPIO_KEY_RESET 12 +#define ICONNECT_GPIO_KEY_OTB 35 + +#define ICONNECT_SW_RESET 0x00 +#define ICONNECT_SW_OTB 0x01 + +static struct gpio_keys_button iconnect_buttons[] = { + { + .type = EV_SW, + .code = ICONNECT_SW_RESET, + .gpio = ICONNECT_GPIO_KEY_RESET, + .desc = "Reset Button", + .active_low = 1, + .debounce_interval = 100, + }, + { + .type = EV_SW, + .code = ICONNECT_SW_OTB, + .gpio = ICONNECT_GPIO_KEY_OTB, + .desc = "OTB Button", + .active_low = 1, + .debounce_interval = 100, + }, +}; + +static struct gpio_keys_platform_data iconnect_button_data = { + .buttons = iconnect_buttons, + .nbuttons = ARRAY_SIZE(iconnect_buttons), +}; + +static struct platform_device iconnect_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &iconnect_button_data, + }, +}; + +static unsigned int iconnect_mpp_config[] __initdata = { + MPP12_GPIO, /*Input for reset button*/ + MPP35_GPIO, /*Input for OTB button*/ + MPP41_GPIO, + MPP42_GPIO, + MPP43_GPIO, + MPP44_GPIO, + MPP45_GPIO, + MPP46_GPIO, + MPP47_GPIO, + MPP48_GPIO, + 0 +}; + +static struct i2c_board_info __initdata iconnect_i2c_rtc = { + I2C_BOARD_INFO("lm63", 0x4c), +}; + +static void __init iconnect_init(void) +{ + u32 dev, rev; + + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(iconnect_mpp_config); + + kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 40); + kirkwood_ehci_init(); + + kirkwood_ge00_init(&iconnect_ge00_data); + kirkwood_pcie_id(&dev, &rev); + + kirkwood_uart0_init(); + + platform_device_register(&iconnect_leds); + platform_device_register(&iconnect_button_device); + + kirkwood_i2c_init(); + i2c_register_board_info(0, &iconnect_i2c_rtc, 1); + +} + +static int __init iconnect_pci_init(void) +{ + if (machine_is_iconnect()) + kirkwood_pcie_init(KW_PCIE0); + + return 0; +} +subsys_initcall(iconnect_pci_init); + + +MACHINE_START(ICONNECT, "Iomega iConnect Wireless") + .atag_offset = 0x100, + .init_machine = iconnect_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/ionics-stratus-setup.c b/arch/arm/mach-kirkwood/ionics-stratus-setup.c --- a/arch/arm/mach-kirkwood/ionics-stratus-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/ionics-stratus-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,137 @@ +/* + * arch/arm/mach-kirkwood/ionics-stratus-setup.c + * + * Ionics Stratus Board Setup arcNumber 4184 + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition ionics_stratus_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data ionics_stratus_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mvsdio_platform_data ionics_stratus_mvsdio_data = { + /* unfortunately the CD signal has not been connected */ +}; + +static struct gpio_led ionics_stratus_led_pins[] = { + { + .name = "status:green:led1", + .default_trigger = "none", + .gpio = 44, + .active_low = 1, + }, + { + .name = "status:green:led2", + .default_trigger = "none", + .gpio = 40, + .active_low = 1, + }, + { + .name = "status:green:led3", + .default_trigger = "default-on", + .gpio = 36, + .active_low = 1, + }, + { + .name = "status:green:led4", + .default_trigger = "default-on", + .gpio = 39, + .active_low = 1, + }, + +}; + +static struct gpio_led_platform_data ionics_stratus_led_data = { + .leds = ionics_stratus_led_pins, + .num_leds = ARRAY_SIZE(ionics_stratus_led_pins), +}; + +static struct platform_device ionics_stratus_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ionics_stratus_led_data, + } +}; + +static unsigned int ionics_stratus_mpp_config[] __initdata = { + MPP21_GPIO, /* USB PORT 1 Pw Enable */ + MPP32_GPIO, /* USB PORT 2 Pw Enable */ + MPP48_GPIO, /* WIFI Power Down */ + MPP49_GPIO, /* WIFI Host Wakeup */ + MPP42_GPIO, /* WIFI MAC Wakeup */ + MPP44_GPIO, /* LED 1 */ + MPP40_GPIO, /* LED 2 */ + MPP36_GPIO, /* LED 3 */ + MPP39_GPIO, /* LED 4 */ + MPP23_GPIO, /* BTN 1 */ + MPP37_GPIO, /* BTN 2 */ + MPP38_GPIO, /* BTN 3 */ + 0 +}; + +static void __init ionics_stratus_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(ionics_stratus_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(ionics_stratus_nand_parts), 25); + + kirkwood_ehci_init(); + + kirkwood_ge00_init(&ionics_stratus_ge00_data); + kirkwood_sdio_init(&ionics_stratus_mvsdio_data); + + platform_device_register(&ionics_stratus_leds); +} + +MACHINE_START(IONICS_STRATUS, "Ionics Plug Computer Plus - Stratus") + /* Maintainer: Mike Brown */ + .atag_offset = 0x100, + .init_machine = ionics_stratus_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig --- a/arch/arm/mach-kirkwood/Kconfig 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/Kconfig 2012-10-10 14:47:05.000000000 -0400 @@ -58,12 +58,6 @@ Say 'Y' here if you want your kernel to support the Marvell DreamPlug (Flattened Device Tree). -config MACH_ICONNECT_DT - bool "Iomega Iconnect (Flattened Device Tree)" - select ARCH_KIRKWOOD_DT - help - Say 'Y' here to enable Iomega Iconnect support. - config MACH_DLINK_KIRKWOOD_DT bool "D-Link Kirkwood-based NAS (Flattened Device Tree)" select ARCH_KIRKWOOD_DT @@ -80,27 +74,6 @@ RaidSonic IB-NAS6210 & IB-NAS6220 devices, using Flattened Device Tree. -config MACH_TS219_DT - bool "Device Tree for QNAP TS-11X, TS-21X NAS" - select ARCH_KIRKWOOD_DT - select ARM_APPENDED_DTB - select ARM_ATAG_DTB_COMPAT - help - Say 'Y' here if you want your kernel to support the QNAP - TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and - TS-219P+ Turbo NAS devices using Fattened Device Tree. - There are two different Device Tree descriptions, depending - on if the device is based on an if the board uses the MV6281 - or MV6282. If you have the wrong one, the buttons will not - work. - -config MACH_GOFLEXNET_DT - bool "Seagate GoFlex Net (Flattened Device Tree)" - select ARCH_KIRKWOOD_DT - help - Say 'Y' here if you want your kernel to support the - Seagate GoFlex Net (Flattened Device Tree). - config MACH_LSXL_DT bool "Buffalo Linkstation LS-XHL, LS-CHLv2 (Flattened Device Tree)" select ARCH_KIRKWOOD_DT @@ -129,6 +102,54 @@ Say 'Y' here if you want your kernel to support the Seagate FreeAgent DockStar. +config MACH_GOFLEXNET + bool "Seagate GoFlex Net" + help + Say 'Y' here if you want your kernel to support the + Seagate GoFlex Net. + +config MACH_GOFLEXHOME + bool "Seagate GoFlex Home" + help + Say 'Y' here if you want your kernel to support the + Seagate GoFlex Home. + +config MACH_ICONNECT + bool "Iomega iConnect Wireless" + help + Say 'Y' here if you want your kernel to support the + Iomega iConnect Wireless. + +config MACH_POGOPLUGV4 + bool "Pogoplug Series 4" + help + Say 'Y' here if you want your kernel to support the + Pogoplug Series 4. + +config MACH_POGO_E02 + bool "CE Pogoplug E02" + help + Say 'Y' here if you want your kernel to support the + CloudEngines Pogoplug e02. + +config MACH_NAS6210 + bool "RaidSonic ICY BOX IB-NAS6210" + help + Say 'Y' here if you want your kernel to support the + RaidSonic ICY BOX IB-NAS6210 device. + +config MACH_TOPKICK + bool "USI Topkick" + help + Say 'Y' here if you want your kernel to support the + USI Topkick. + +config MACH_IONICS_STRATUS + bool "Ionics Stratus" + help + Say 'Y' here if you want your kernel to support the + Ionics Stratus. + config MACH_OPENRD bool @@ -195,6 +216,18 @@ Say 'Y' here if you want your kernel to support the HP t5325 Thin Client. +config MACH_NSA310 + bool "ZyXEL NSA310 1-Bay Power Media Server" + help + Say 'Y' here if you want your kernel to support the + ZyXEL NSA310. + +config MACH_NSA320 + bool "ZyXEL NSA320 2-Bay Power Media Server" + help + Say 'Y' here if you want your kernel to support the + ZyXel NSA320. + endmenu endif diff -ruN a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile --- a/arch/arm/mach-kirkwood/Makefile 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/Makefile 2012-10-10 14:47:50.000000000 -0400 @@ -8,6 +8,14 @@ obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o +obj-$(CONFIG_MACH_GOFLEXNET) += goflexnet-setup.o +obj-$(CONFIG_MACH_GOFLEXHOME) += goflexhome-setup.o +obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o +obj-$(CONFIG_MACH_POGOPLUGV4) += pogoplugv4-setup.o +obj-$(CONFIG_MACH_POGO_E02) += pogo_e02-setup.o +obj-$(CONFIG_MACH_NAS6210) += nas6210-setup.o +obj-$(CONFIG_MACH_TOPKICK) += topkick-setup.o +obj-$(CONFIG_MACH_IONICS_STRATUS) += ionics-stratus-setup.o obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o @@ -18,13 +26,12 @@ obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o obj-$(CONFIG_MACH_T5325) += t5325-setup.o +obj-$(CONFIG_MACH_NSA310) += nsa310-setup.o +obj-$(CONFIG_MACH_NSA320) += nsa320-setup.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o obj-$(CONFIG_MACH_DREAMPLUG_DT) += board-dreamplug.o -obj-$(CONFIG_MACH_ICONNECT_DT) += board-iconnect.o obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += board-dnskw.o obj-$(CONFIG_MACH_IB62X0_DT) += board-ib62x0.o -obj-$(CONFIG_MACH_TS219_DT) += board-ts219.o tsx1x-common.o -obj-$(CONFIG_MACH_GOFLEXNET_DT) += board-goflexnet.o obj-$(CONFIG_MACH_LSXL_DT) += board-lsxl.o diff -ruN a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot --- a/arch/arm/mach-kirkwood/Makefile.boot 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/Makefile.boot 2012-10-10 14:48:04.000000000 -0400 @@ -5,10 +5,6 @@ dtb-$(CONFIG_MACH_DREAMPLUG_DT) += kirkwood-dreamplug.dtb dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns320.dtb dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb -dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb -dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-ts219-6281.dtb -dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-ts219-6282.dtb -dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb diff -ruN a/arch/arm/mach-kirkwood/nas6210-setup.c b/arch/arm/mach-kirkwood/nas6210-setup.c --- a/arch/arm/mach-kirkwood/nas6210-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/nas6210-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,186 @@ +/* + * arch/arm/mach-kirkwood/nas6210-setup.c + * + * Raidsonic ICYBOX NAS6210 Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +#define NAS6210_GPIO_POWER_OFF 24 + +static struct mtd_partition nas6210_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = 6*SZ_1M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data nas6210_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(8), +}; + +static struct mv_sata_platform_data nas6210_sata_data = { + .n_ports = 2, +}; + +static struct gpio_led nas6210_led_pins[] = { + { + .name = "status:green:power", + .default_trigger = "default-on", + .gpio = 25, + .active_low = 0, + }, + { + .name = "status:red:power", + .default_trigger = "none", + .gpio = 22, + .active_low = 0, + }, + { + .name = "status:red:usb_copy", + .default_trigger = "none", + .gpio = 27, + .active_low = 0, + }, +}; + +static struct gpio_led_platform_data nas6210_led_data = { + .leds = nas6210_led_pins, + .num_leds = ARRAY_SIZE(nas6210_led_pins), +}; + +static struct platform_device nas6210_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &nas6210_led_data, + } +}; + +static struct gpio_keys_button nas6210_buttons[] = { + { + .code = KEY_COPY, + .gpio = 29, + .desc = "USB Copy", + .active_low = 1, + }, + { + .code = KEY_RESTART, + .gpio = 28, + .desc = "Reset", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data nas6210_button_data = { + .buttons = nas6210_buttons, + .nbuttons = ARRAY_SIZE(nas6210_buttons), +}; + +static struct platform_device nas6210_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &nas6210_button_data, + } +}; + +static unsigned int nas6210_mpp_config[] __initdata = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP22_GPIO, /* Power LED red */ + MPP24_GPIO, /* Power off device */ + MPP25_GPIO, /* Power LED green */ + MPP27_GPIO, /* USB transfer LED */ + MPP28_GPIO, /* Reset button */ + MPP29_GPIO, /* USB Copy button */ + 0 +}; + +static void nas6210_power_off(void) +{ + gpio_set_value(NAS6210_GPIO_POWER_OFF, 1); +} + +static void __init nas6210_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(nas6210_mpp_config); + + kirkwood_nand_init(ARRAY_AND_SIZE(nas6210_nand_parts), 25); + kirkwood_ehci_init(); + kirkwood_ge00_init(&nas6210_ge00_data); + kirkwood_sata_init(&nas6210_sata_data); + kirkwood_uart0_init(); + platform_device_register(&nas6210_leds); + platform_device_register(&nas6210_button_device); + if (gpio_request(NAS6210_GPIO_POWER_OFF, "power-off") == 0 && + gpio_direction_output(NAS6210_GPIO_POWER_OFF, 0) == 0) + pm_power_off = nas6210_power_off; + else + pr_err("nas6210: failed to configure power-off GPIO\n"); +} + +static int __init nas6210_pci_init(void) +{ + if (machine_is_nas6210()) { + u32 dev, rev; + + kirkwood_pcie_id(&dev, &rev); + if (dev == MV88F6282_DEV_ID) + kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0); + else + kirkwood_pcie_init(KW_PCIE0); + } + + return 0; +} +subsys_initcall(nas6210_pci_init); + +MACHINE_START(NAS6210, "RaidSonic ICY BOX IB-NAS6210") + /* Maintainer: */ + .atag_offset = 0x100, + .init_machine = nas6210_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/nsa310-setup.c b/arch/arm/mach-kirkwood/nsa310-setup.c --- a/arch/arm/mach-kirkwood/nsa310-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/nsa310-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,299 @@ +/* + * arch/arm/mach-kirkwood/nsa310-setup.c + * + * ZyXEL NSA310 1-Bay Power Media Server Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include /* for SPEED_1000, DUPLEX_FULL */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition nsa310_nand_parts[] = { + { + .name = "uboot", + .offset = 0, + .size = SZ_1M, + .mask_flags = MTD_WRITEABLE + }, { + .name = "uboot_env", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "key_store", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "info", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "etc", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "kernel_1", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "rootfs1", + .offset = MTDPART_OFS_NXTBLK, + .size = 48 * SZ_1M - SZ_256K + }, { + .name = "kernel_2", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "rootfs2", + .offset = MTDPART_OFS_NXTBLK, + .size = 48 * SZ_1M - SZ_256K + }, +}; + +static struct mv_sata_platform_data nsa310_sata_data = { + .n_ports = 2, +}; + +static struct gpio_keys_button nsa310_button_pins[] = { + { + .code = KEY_RESTART, + .gpio = 36, + .desc = "Reset", + .active_low = 1, + }, { + .code = KEY_COPY, + .gpio = 37, + .desc = "Copy", + .active_low = 1, + }, { + .code = KEY_POWER, + .gpio = 46, + .desc = "Power", + .active_low = 0, + }, +}; + +static struct gpio_keys_platform_data nsa310_button_data = { + .buttons = nsa310_button_pins, + .nbuttons = ARRAY_SIZE(nsa310_button_pins), +}; + +static struct platform_device nsa310_buttons = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &nsa310_button_data, + }, +}; + +static struct gpio_led nsa310_led_pins[] = { + { + .name = "nsa310:green:hdd2", + .default_trigger = "default-off", + .gpio = 12, + .active_low = 0, + }, { + .name = "nsa310:red:hdd2", + .default_trigger = "default-off", + .gpio = 13, + .active_low = 0, + }, { + .name = "nsa310:green:usb", + .default_trigger = "default-off", + .gpio = 15, + .active_low = 0, + }, { + .name = "nsa310:green:sys", + .default_trigger = "default-off", + .gpio = 28, + .active_low = 0, + }, { + .name = "nsa310:orange:sys", + .default_trigger = "default-on", + .gpio = 29, + .active_low = 0, + }, { + .name = "nsa310:green:copy", + .default_trigger = "default-off", + .gpio = 39, + .active_low = 0, + }, { + .name = "nsa310:red:copy", + .default_trigger = "default-off", + .gpio = 40, + .active_low = 0, + }, { + .name = "nsa310:green:hdd1", + .default_trigger = "default-off", + .gpio = 41, + .active_low = 0, + }, { + .name = "nsa310:red:hdd1", + .default_trigger = "default-off", + .gpio = 42, + .active_low = 0, + }, +}; + +static struct gpio_led_platform_data nsa310_led_data = { + .leds = nsa310_led_pins, + .num_leds = ARRAY_SIZE(nsa310_led_pins), +}; + +static struct platform_device nsa310_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &nsa310_led_data, + }, +}; + +static struct nsa3xx_hwmon_platform_data nsa310_hwmon_data = { + /* GPIOs connected to Holtek HT46R065 MCU */ + .act_pin = 17, + .clk_pin = 16, + .data_pin = 14, +}; + +static struct platform_device nsa310_hwmon = { + .name = "nsa3xx-hwmon", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &nsa310_hwmon_data, + }, +}; + +static unsigned int nsa310_mpp_config[] __initdata = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW0_SDA, /* PCF8563 RTC chip */ + MPP9_TW0_SCK, /* connected to TWSI */ + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* HDD2 LED (green) */ + MPP13_GPIO, /* HDD2 LED (red) */ + MPP14_GPIO, /* MCU DATA pin (in) */ + MPP15_GPIO, /* USB LED (green) */ + MPP16_GPIO, /* MCU CLK pin (out) */ + MPP17_GPIO, /* MCU ACT pin (out) */ + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GPIO, + MPP21_GPIO, /* USB power */ + MPP22_GPIO, + MPP23_GPIO, + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, /* SYS LED (green) */ + MPP29_GPIO, /* SYS LED (orange) */ + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GPO, + MPP34_GPIO, + MPP35_GPIO, + MPP36_GPIO, /* reset button */ + MPP37_GPIO, /* copy button */ + MPP38_GPIO, /* VID B0 */ + MPP39_GPIO, /* COPY LED (green) */ + MPP40_GPIO, /* COPY LED (red) */ + MPP41_GPIO, /* HDD1 LED (green) */ + MPP42_GPIO, /* HDD1 LED (red) */ + MPP43_GPIO, /* HTP pin */ + MPP44_GPIO, /* buzzer */ + MPP45_GPIO, /* VID B1 */ + MPP46_GPIO, /* power button */ + MPP47_GPIO, /* power resume data */ + MPP48_GPIO, /* power off */ + MPP49_GPIO, /* power resume clock */ + 0 +}; + +#define NSA310_GPIO_USB_POWER 21 +#define NSA310_GPIO_POWER_OFF 48 + +static void nsa310_power_off(void) +{ + gpio_set_value(NSA310_GPIO_POWER_OFF, 1); +} + +static int __initdata usb_power = 1; /* default "on" */ + +static int __init nsa310_usb_power(char *str) +{ + usb_power = strncmp(str, "off", 3) ? 1 : 0; + return 1; +} +/* Parse boot_command_line string nsa310_usb_power=on|off */ +__setup("nsa310_usb_power=", nsa310_usb_power); + +static void __init nsa310_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(nsa310_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(nsa310_nand_parts), 40); + + kirkwood_i2c_init(); + + if (gpio_request(NSA310_GPIO_USB_POWER, "USB Power Enable") || + gpio_direction_output(NSA310_GPIO_USB_POWER, usb_power)) + pr_err("nsa310: failed to configure USB power enable GPIO)\n"); + gpio_free(NSA310_GPIO_USB_POWER); + + kirkwood_ehci_init(); + kirkwood_sata_init(&nsa310_sata_data); + platform_device_register(&nsa310_leds); + platform_device_register(&nsa310_buttons); + platform_device_register(&nsa310_hwmon); + + if (gpio_request(NSA310_GPIO_POWER_OFF, "power-off") || + gpio_direction_output(NSA310_GPIO_POWER_OFF, 0)) + pr_err("nsa310: failed to configure power-off GPIO\n"); + else + pm_power_off = nsa310_power_off; +} + +MACHINE_START(NSA310, "ZyXEL NSA310 1-Bay Power Media Server") + /* Maintainer: Peter Oostewechel */ + .atag_offset = 0x100, + .init_machine = nsa310_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/nsa320-setup.c b/arch/arm/mach-kirkwood/nsa320-setup.c --- a/arch/arm/mach-kirkwood/nsa320-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/nsa320-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,308 @@ +/* + * arch/arm/mach-kirkwood/nsa320-setup.c + * + * ZyXEL NSA320 2-Bay Power Media Server Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition nsa320_nand_parts[] = { + { + .name = "uboot", + .offset = 0, + .size = SZ_1M, + .mask_flags = MTD_WRITEABLE + }, { + .name = "uboot_env", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "key_store", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "info", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_512K + }, { + .name = "etc", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "kernel_1", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "rootfs1", + .offset = MTDPART_OFS_NXTBLK, + .size = 48 * SZ_1M - SZ_256K + }, { + .name = "kernel_2", + .offset = MTDPART_OFS_NXTBLK, + .size = 10 * SZ_1M + }, { + .name = "rootfs2", + .offset = MTDPART_OFS_NXTBLK, + .size = 48 * SZ_1M - SZ_256K + }, +}; + +static struct i2c_board_info __initdata nsa320_i2c_rtc = { + I2C_BOARD_INFO("pcf8563", 0x51), +}; + +static struct mv643xx_eth_platform_data nsa320_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(1), +}; + +static struct mv_sata_platform_data nsa320_sata_data = { + .n_ports = 2, +}; + +static struct gpio_keys_button nsa320_button_pins[] = { + { + .code = KEY_RESTART, + .gpio = 36, + .desc = "Reset", + .active_low = 1, + }, { + .code = KEY_COPY, + .gpio = 37, + .desc = "Copy", + .active_low = 1, + }, { + .code = KEY_POWER, + .gpio = 46, + .desc = "Power", + .active_low = 0, + }, +}; + +static struct gpio_keys_platform_data nsa320_button_data = { + .buttons = nsa320_button_pins, + .nbuttons = ARRAY_SIZE(nsa320_button_pins), +}; + +static struct platform_device nsa320_buttons = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &nsa320_button_data, + }, +}; + +static struct gpio_led nsa320_led_pins[] = { + { + .name = "nsa320:green:hdd2", + .default_trigger = "default-off", + .gpio = 12, + .active_low = 0, + }, { + .name = "nsa320:red:hdd2", + .default_trigger = "default-off", + .gpio = 13, + .active_low = 0, + }, { + .name = "nsa320:green:usb", + .default_trigger = "default-off", + .gpio = 15, + .active_low = 0, + }, { + .name = "nsa320:green:sys", + .default_trigger = "default-off", + .gpio = 28, + .active_low = 0, + }, { + .name = "nsa320:orange:sys", + .default_trigger = "default-on", + .gpio = 29, + .active_low = 0, + }, { + .name = "nsa320:green:copy", + .default_trigger = "default-off", + .gpio = 39, + .active_low = 0, + }, { + .name = "nsa320:red:copy", + .default_trigger = "default-off", + .gpio = 40, + .active_low = 0, + }, { + .name = "nsa320:green:hdd1", + .default_trigger = "default-off", + .gpio = 41, + .active_low = 0, + }, { + .name = "nsa320:red:hdd1", + .default_trigger = "default-off", + .gpio = 42, + .active_low = 0, + }, +}; + +static struct gpio_led_platform_data nsa320_led_data = { + .leds = nsa320_led_pins, + .num_leds = ARRAY_SIZE(nsa320_led_pins), +}; + +static struct platform_device nsa320_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &nsa320_led_data, + }, +}; + +static struct nsa3xx_hwmon_platform_data nsa320_hwmon_data = { + /* GPIOs connected to Holtek HT46R065 MCU */ + .act_pin = 17, + .clk_pin = 16, + .data_pin = 14, +}; + +static struct platform_device nsa320_hwmon = { + .name = "nsa3xx-hwmon", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &nsa320_hwmon_data, + }, +}; + +static unsigned int nsa320_mpp_config[] __initdata = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW0_SDA, /* PCF8563 RTC chip */ + MPP9_TW0_SCK, /* connected to TWSI */ + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* HDD2 LED (green) */ + MPP13_GPIO, /* HDD2 LED (red) */ + MPP14_GPIO, /* MCU DATA pin (in) */ + MPP15_GPIO, /* USB LED (green) */ + MPP16_GPIO, /* MCU CLK pin (out) */ + MPP17_GPIO, /* MCU ACT pin (out) */ + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GPIO, + MPP21_GPIO, /* USB power */ + MPP22_GPIO, + MPP23_GPIO, + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, /* SYS LED (green) */ + MPP29_GPIO, /* SYS LED (orange) */ + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GPO, + MPP34_GPIO, + MPP35_GPIO, + MPP36_GPIO, /* reset button */ + MPP37_GPIO, /* copy button */ + MPP38_GPIO, /* VID B0 */ + MPP39_GPIO, /* COPY LED (green) */ + MPP40_GPIO, /* COPY LED (red) */ + MPP41_GPIO, /* HDD1 LED (green) */ + MPP42_GPIO, /* HDD1 LED (red) */ + MPP43_GPIO, /* HTP pin */ + MPP44_GPIO, /* buzzer */ + MPP45_GPIO, /* VID B1 */ + MPP46_GPIO, /* power button */ + MPP47_GPIO, /* power resume data */ + MPP48_GPIO, /* power off */ + MPP49_GPIO, /* power resume clock */ + 0 +}; + +#define NSA320_GPIO_USB_POWER 21 +#define NSA320_GPIO_POWER_OFF 48 + +static void nsa320_power_off(void) +{ + gpio_set_value(NSA320_GPIO_POWER_OFF, 1); +} + +static int __initdata usb_power = 1; /* default "on" */ + +static int __init nsa320_usb_power(char *str) +{ + usb_power = strncmp(str, "off", 3) ? 1 : 0; + return 1; +} +/* Parse boot_command_line string nsa320_usb_power=on|off */ +__setup("nsa320_usb_power=", nsa320_usb_power); + +static void __init nsa320_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(nsa320_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(nsa320_nand_parts), 40); + + kirkwood_i2c_init(); + i2c_register_board_info(0, &nsa320_i2c_rtc, 1); + + if (gpio_request(NSA320_GPIO_USB_POWER, "USB Power Enable") || + gpio_direction_output(NSA320_GPIO_USB_POWER, usb_power)) + pr_err("nsa320: failed to configure USB power enable GPIO)\n"); + gpio_free(NSA320_GPIO_USB_POWER); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&nsa320_ge00_data); + kirkwood_sata_init(&nsa320_sata_data); + platform_device_register(&nsa320_leds); + platform_device_register(&nsa320_buttons); + platform_device_register(&nsa320_hwmon); + + if (gpio_request(NSA320_GPIO_POWER_OFF, "power-off") || + gpio_direction_output(NSA320_GPIO_POWER_OFF, 0)) + pr_err("nsa320: failed to configure power-off GPIO\n"); + else + pm_power_off = nsa320_power_off; +} + +MACHINE_START(NSA320, "ZyXEL NSA320 2-Bay Power Media Server") + /* Maintainer: Peter Schildmann */ + .atag_offset = 0x100, + .init_machine = nsa320_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/pogo_e02-setup.c b/arch/arm/mach-kirkwood/pogo_e02-setup.c --- a/arch/arm/mach-kirkwood/pogo_e02-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/pogo_e02-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,115 @@ +/* + * arch/arm/mach-kirkwood/pogo_e02-setup.c + * + * CloudEngines Pogoplug E02 support + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition pogo_e02_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { + .name = "pogoplug", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_32M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data pogo_e02_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct gpio_led pogo_e02_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 48, + .active_low = 1, + }, + { + .name = "status:orange:fault", + .default_trigger = "none", + .gpio = 49, + .active_low = 1, + } +}; + +static struct gpio_led_platform_data pogo_e02_led_data = { + .leds = pogo_e02_led_pins, + .num_leds = ARRAY_SIZE(pogo_e02_led_pins), +}; + +static struct platform_device pogo_e02_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &pogo_e02_led_data, + } +}; + +static unsigned int pogo_e02_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP48_GPIO, /* LED Green */ + MPP49_GPIO, /* LED Orange */ + 0 +}; + +static void __init pogo_e02_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(pogo_e02_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(pogo_e02_nand_parts), 25); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + + kirkwood_ge00_init(&pogo_e02_ge00_data); + + platform_device_register(&pogo_e02_leds); +} + +MACHINE_START(POGO_E02, "Pogoplug E02") + .atag_offset = 0x100, + .init_machine = pogo_e02_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/pogoplugv4-setup.c b/arch/arm/mach-kirkwood/pogoplugv4-setup.c --- a/arch/arm/mach-kirkwood/pogoplugv4-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/pogoplugv4-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,194 @@ +/* + * arch/arm/mach-kirkwood/pogoplugv4-setup.c + * + * Pogoplug Series 4 Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +#define POGOPLUGV4_GPIO_USB_VBUS 10 + +static struct mtd_partition ppv4_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = 2 * SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = 3 * SZ_1M + }, { + .name = "uImage2", + .offset = MTDPART_OFS_NXTBLK, + .size = 3 * SZ_1M + }, { + .name = "failsafe", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_8M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data pogoplugv4_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data pogoplugv4_sata_data = { + .n_ports = 1, +}; + +static struct gpio_keys_button pogoplugv4_button_pins[] = { + { + .code = KEY_EJECTCD, + .gpio = 29, + .desc = "Eject Button", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data pogoplugv4_button_data = { + .buttons = pogoplugv4_button_pins, + .nbuttons = ARRAY_SIZE(pogoplugv4_button_pins), +}; + +static struct platform_device pogoplugv4_buttons = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &pogoplugv4_button_data, + }, +}; + +static struct gpio_led pogoplugv4_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 22, + .active_low = 1, + }, + { + .name = "status:red:fault", + .default_trigger = "none", + .gpio = 24, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data pogoplugv4_led_data = { + .leds = pogoplugv4_led_pins, + .num_leds = ARRAY_SIZE(pogoplugv4_led_pins), +}; + +static struct platform_device pogoplugv4_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &pogoplugv4_led_data, + } +}; + +static struct mvsdio_platform_data ppv4_mvsdio_data = { + .gpio_card_detect = 27, +}; + +static unsigned int ppv4_mpp_config[] __initdata = { + MPP27_GPIO, /* SD card detect */ + MPP29_GPIO, /* Eject button */ + MPP22_GPIO, /* Green LED */ + MPP24_GPIO, /* Red LED */ + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + 0 +}; + +static const struct flash_platform_data pogoplugv4_spi_slave_data = { + .type = "m25p05-nonjedec", +}; + +static struct spi_board_info __initdata pogoplugv4_spi_slave_info[] = { + { + .modalias = "m25p05-nonjedec", + .platform_data = &pogoplugv4_spi_slave_data, + .irq = -1, + .max_speed_hz = 20000000, + .bus_num = 0, + .chip_select = 0, + }, +}; + +static void __init pogoplugv4_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(ppv4_mpp_config); + + orion_gpio_set_valid(POGOPLUGV4_GPIO_USB_VBUS, 1); + if (gpio_request(POGOPLUGV4_GPIO_USB_VBUS, "USB VBUS") != 0 || + gpio_direction_output(POGOPLUGV4_GPIO_USB_VBUS, 1) != 0) + pr_err("POGOPLUGV4: failed to setup USB VBUS GPIO\n"); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&pogoplugv4_ge00_data); + kirkwood_sata_init(&pogoplugv4_sata_data); + spi_register_board_info(pogoplugv4_spi_slave_info, + ARRAY_SIZE(pogoplugv4_spi_slave_info)); + kirkwood_spi_init(); + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(ppv4_nand_parts), 25); + kirkwood_sdio_init(&ppv4_mvsdio_data); + platform_device_register(&pogoplugv4_leds); + platform_device_register(&pogoplugv4_buttons); +} + +static int __init pogoplugv4_pci_init(void) +{ + if (machine_is_pogoplugv4()) + kirkwood_pcie_init(KW_PCIE0); + + return 0; +} +subsys_initcall(pogoplugv4_pci_init); + +MACHINE_START(POGOPLUGV4, "Pogoplug V4") + /* Maintainer: Kevin Mihelich */ + .atag_offset = 0x100, + .init_machine = pogoplugv4_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c --- a/arch/arm/mach-kirkwood/sheevaplug-setup.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -43,7 +43,7 @@ .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -static struct mv_sata_platform_data sheeva_esata_sata_data = { +static struct mv_sata_platform_data esata_sheevaplug_sata_data = { .n_ports = 2, }; @@ -51,7 +51,7 @@ /* unfortunately the CD signal has not been connected */ }; -static struct mvsdio_platform_data sheeva_esata_mvsdio_data = { +static struct mvsdio_platform_data esata_sheevaplug_mvsdio_data = { .gpio_write_protect = 44, /* MPP44 used as SD write protect */ .gpio_card_detect = 47, /* MPP47 used as SD card detect */ }; @@ -64,7 +64,13 @@ .active_low = 1, }, { - .name = "plug:green:health", + .name = "status:green:health", + .default_trigger = "none", + .gpio = 48, + .active_low = 1, + }, + { + .name = "status:blue:health", .default_trigger = "default-on", .gpio = 49, .active_low = 1, @@ -87,15 +93,18 @@ static unsigned int sheevaplug_mpp_config[] __initdata = { MPP29_GPIO, /* USB Power Enable */ MPP46_GPIO, /* LED Red */ - MPP49_GPIO, /* LED */ + MPP48_GPIO, /* LED Green */ + MPP49_GPIO, /* LED Blue */ 0 }; -static unsigned int sheeva_esata_mpp_config[] __initdata = { +static unsigned int esata_sheevaplug_mpp_config[] __initdata = { MPP29_GPIO, /* USB Power Enable */ MPP44_GPIO, /* SD Write Protect */ MPP47_GPIO, /* SD Card Detect */ - MPP49_GPIO, /* LED Green */ + MPP46_GPIO, /* LED Red */ + MPP48_GPIO, /* LED Green */ + MPP49_GPIO, /* LED Blue */ 0 }; @@ -108,7 +117,7 @@ /* setup gpio pin select */ if (machine_is_esata_sheevaplug()) - kirkwood_mpp_conf(sheeva_esata_mpp_config); + kirkwood_mpp_conf(esata_sheevaplug_mpp_config); else kirkwood_mpp_conf(sheevaplug_mpp_config); @@ -124,11 +133,11 @@ /* honor lower power consumption for plugs with out eSATA */ if (machine_is_esata_sheevaplug()) - kirkwood_sata_init(&sheeva_esata_sata_data); + kirkwood_sata_init(&esata_sheevaplug_sata_data); /* enable sd wp and sd cd on plugs with esata */ if (machine_is_esata_sheevaplug()) - kirkwood_sdio_init(&sheeva_esata_mvsdio_data); + kirkwood_sdio_init(&esata_sheevaplug_mvsdio_data); else kirkwood_sdio_init(&sheevaplug_mvsdio_data); diff -ruN a/arch/arm/mach-kirkwood/topkick-setup.c b/arch/arm/mach-kirkwood/topkick-setup.c --- a/arch/arm/mach-kirkwood/topkick-setup.c 1969-12-31 19:00:00.000000000 -0500 +++ b/arch/arm/mach-kirkwood/topkick-setup.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,165 @@ +/* + * arch/arm/mach-kirkwood/topkick-setup.c + * + * USI Topkick Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition topkick_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = 0x180000 + }, { + .name = "u-boot-env", + .offset = 0x180000, + .size = 128 * 1024 + }, { + .name = "uImage", + .offset = 2 * 1024 * 1024, + .size = 6 * 1024 * 1024 + }, { + .name = "rootfs", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data topkick_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data topkick_sata_data = { + .n_ports = 1, +}; + +static struct mvsdio_platform_data topkick_mvsdio_data = { + .gpio_card_detect = 47, /* MPP47 used as SD card detect */ +}; + + +static struct gpio_led topkick_led_pins[] = { + { + .name = "status:blue:disk", + .default_trigger = "none", + .gpio = 21, + .active_low = 1, + }, + { + .name = "status:red:fault", + .default_trigger = "none", + .gpio = 37, + .active_low = 1, + }, + { + .name = "status:blue:health", + .default_trigger = "default-on", + .gpio = 38, + .active_low = 1, + }, + { + .name = "status:green:misc", + .default_trigger = "none", + .gpio = 39, + .active_low = 1, + }, + { + .name = "status:orange:misc", + .default_trigger = "none", + .gpio = 48, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data topkick_led_data = { + .leds = topkick_led_pins, + .num_leds = ARRAY_SIZE(topkick_led_pins), +}; + +static struct platform_device topkick_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &topkick_led_data, + } +}; + +static unsigned int topkick_mpp_config[] __initdata = { + MPP12_SD_CLK, /* SDIO Clock */ + MPP13_SD_CMD, /* SDIO Cmd */ + MPP14_SD_D0, /* SDIO Data 0 */ + MPP15_SD_D1, /* SDIO Data 1 */ + MPP16_SD_D2, /* SDIO Data 2 */ + MPP17_SD_D3, /* SDIO Data 3 */ + MPP21_GPIO, /* LED Blue SATA */ + MPP35_GPIO, /* USB Power Enable */ + MPP36_GPIO, /* SATA Power Enable */ + MPP37_GPIO, /* LED Red System */ + MPP38_GPIO, /* LED Blue System */ + MPP39_GPIO, /* LED Green Misc/WiFi */ + MPP43_GPIO, /* WOL Eth WOL */ + MPP44_GPIO, /* SW GW Mode */ + MPP45_GPIO, /* SW AP Mode */ + MPP46_GPIO, /* SW Power Off */ + MPP47_GPIO, /* SDIO Detect */ + MPP48_GPIO, /* LED Orange Misc/WiFi */ + 0 +}; + +static void __init topkick_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(topkick_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(topkick_nand_parts), 40); + + if (gpio_request(35, "USB Power Enable") != 0 || + gpio_direction_output(35, 1) != 0) + printk(KERN_ERR "can't set up GPIO 35 (USB Power Enable)\n"); + if (gpio_request(36, "SATA Power Enable") != 0 || + gpio_direction_output(36, 1) != 0) + printk(KERN_ERR "can't set up GPIO 36 (SATA Power Enable)\n"); + kirkwood_ge00_init(&topkick_ge00_data); + kirkwood_ehci_init(); + kirkwood_sata_init(&topkick_sata_data); + kirkwood_sdio_init(&topkick_mvsdio_data); + + platform_device_register(&topkick_leds); +} + +MACHINE_START(TOPKICK, "USI Topkick") + /* Maintainer: Mike Brown */ + .atag_offset = 0x100, + .init_machine = topkick_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff -ruN a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c --- a/arch/arm/plat-orion/common.c 2012-10-07 11:41:28.000000000 -0400 +++ b/arch/arm/plat-orion/common.c 2012-10-10 13:37:18.000000000 -0400 @@ -253,7 +253,9 @@ /***************************************************************************** * GE00 ****************************************************************************/ -struct mv643xx_eth_shared_platform_data orion_ge00_shared_data; +struct mv643xx_eth_shared_platform_data orion_ge00_shared_data = { + .tx_csum_limit = 1600, +}; static struct resource orion_ge00_shared_resources[] = { { diff -ruN a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig --- a/drivers/hwmon/Kconfig 2012-10-07 11:41:28.000000000 -0400 +++ b/drivers/hwmon/Kconfig 2012-10-10 13:37:18.000000000 -0400 @@ -1411,6 +1411,19 @@ help Support for the A/D converter on MC13783 and MC13892 PMIC. +config SENSORS_NSA3XX + tristate "ZyXEL NSA3xx fan speed and temperature sensors" + depends on (MACH_NSA310 || MACH_NSA320) && GENERIC_GPIO + help + If you say yes here you get support for hardware monitoring + for the ZyXEL NSA3XX Media Servers. + + The sensor data is taken from a Holtek HT46R065 microcontroller + connected to GPIO lines. + + This driver can also be built as a module. If so, the module + will be called nsa3xx-hwmon. + if ACPI comment "ACPI drivers" diff -ruN a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile --- a/drivers/hwmon/Makefile 2012-10-07 11:41:28.000000000 -0400 +++ b/drivers/hwmon/Makefile 2012-10-10 13:37:18.000000000 -0400 @@ -98,6 +98,7 @@ obj-$(CONFIG_SENSORS_MAX6642) += max6642.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.o obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o +obj-$(CONFIG_SENSORS_NSA3XX) += nsa3xx-hwmon.o obj-$(CONFIG_SENSORS_MCP3021) += mcp3021.o obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o diff -ruN a/drivers/hwmon/nsa3xx-hwmon.c b/drivers/hwmon/nsa3xx-hwmon.c --- a/drivers/hwmon/nsa3xx-hwmon.c 1969-12-31 19:00:00.000000000 -0500 +++ b/drivers/hwmon/nsa3xx-hwmon.c 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,251 @@ +/* + * drivers/hwmon/nsa3xx-hwmon.c + * + * ZyXEL NSA3xx Media Servers + * hardware monitoring + * + * Copyright (C) 2012 Peter Schildmann + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License v2 as published by the + * Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define MAGIC_NUMBER 0x55 + +struct nsa3xx_hwmon { + struct platform_device *pdev; + struct device *classdev; + struct mutex update_lock; /* lock GPIO operations */ + unsigned long last_updated; /* jiffies */ + unsigned long mcu_data; +}; + +enum nsa3xx_inputs { + NSA3XX_FAN = 1, + NSA3XX_TEMP = 0, +}; + +static const char *nsa3xx_input_names[] = { + [NSA3XX_FAN] = "Chassis Fan", + [NSA3XX_TEMP] = "System Temperature", +}; + +static unsigned long nsa3xx_hwmon_update(struct device *dev) +{ + int i; + unsigned long mcu_data; + struct nsa3xx_hwmon *hwmon = dev_get_drvdata(dev); + struct nsa3xx_hwmon_platform_data *pdata = hwmon->pdev->dev.platform_data; + + mutex_lock(&hwmon->update_lock); + + mcu_data = hwmon->mcu_data; + + if (time_after(jiffies, hwmon->last_updated + (3 * HZ)) || mcu_data == 0) { + dev_dbg(dev, "Reading MCU data\n"); + + gpio_set_value(pdata->act_pin, 0); + msleep(100); + + for (i = 31; i >= 0; i--) { + gpio_set_value(pdata->clk_pin, 0); + udelay(100); + + gpio_set_value(pdata->clk_pin, 1); + udelay(100); + + mcu_data |= gpio_get_value(pdata->data_pin) ? (1 << i) : 0; + } + + gpio_set_value(pdata->act_pin, 1); + + if ((mcu_data & 0xff000000) != (MAGIC_NUMBER << 24)) { + dev_err(dev, "Failed to read MCU data\n"); + mcu_data = 0; + } + + hwmon->mcu_data = mcu_data; + hwmon->last_updated = jiffies; + } + + mutex_unlock(&hwmon->update_lock); + + return mcu_data; +} + +static ssize_t show_name(struct device *dev, + struct device_attribute *attr, char *buf) +{ + return sprintf(buf, "nsa3xx\n"); +} + +static ssize_t show_label(struct device *dev, + struct device_attribute *attr, char *buf) +{ + int channel = to_sensor_dev_attr(attr)->index; + return sprintf(buf, "%s\n", nsa3xx_input_names[channel]); +} + +static ssize_t show_value(struct device *dev, + struct device_attribute *attr, char *buf) +{ + int channel = to_sensor_dev_attr(attr)->index; + unsigned long mcu_data = nsa3xx_hwmon_update(dev); + unsigned long value = 0; + switch(channel) { + case NSA3XX_TEMP: + value = (mcu_data & 0xffff) * 100; + break; + case NSA3XX_FAN: + value = ((mcu_data & 0xff0000) >> 16) * 100; + break; + } + return sprintf(buf, "%lu\n", value); +} + +static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); +static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_label, NULL, NSA3XX_TEMP); +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_value, NULL, NSA3XX_TEMP); +static SENSOR_DEVICE_ATTR(fan1_label, S_IRUGO, show_label, NULL, NSA3XX_FAN); +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_value, NULL, NSA3XX_FAN); + +static struct attribute *nsa3xx_attributes[] = { + &dev_attr_name.attr, + &sensor_dev_attr_temp1_label.dev_attr.attr, + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_fan1_label.dev_attr.attr, + &sensor_dev_attr_fan1_input.dev_attr.attr, + NULL +}; + +static const struct attribute_group nsa3xx_attr_group = { + .attrs = nsa3xx_attributes, +}; + +static int nsa3xx_hwmon_request_gpios(struct nsa3xx_hwmon_platform_data *pdata) +{ + int ret; + + if ((ret = gpio_request(pdata->act_pin, "act pin"))) + return ret; + + if ((ret = gpio_request(pdata->clk_pin, "clk pin"))) + return ret; + + if ((ret = gpio_request(pdata->data_pin, "data pin"))) + return ret; + + if ((ret = gpio_direction_output(pdata->act_pin, 1))) + return ret; + + if ((ret = gpio_direction_output(pdata->clk_pin, 1))) + return ret; + + if ((ret = gpio_direction_input(pdata->data_pin))) + return ret; + + return 0; +} + +static void nsa3xx_hwmon_free_gpios(struct nsa3xx_hwmon_platform_data *pdata) +{ + gpio_free(pdata->act_pin); + gpio_free(pdata->clk_pin); + gpio_free(pdata->data_pin); +} + +static int __devinit nsa3xx_hwmon_probe(struct platform_device *pdev) +{ + int ret; + struct nsa3xx_hwmon *hwmon; + struct nsa3xx_hwmon_platform_data *pdata = pdev->dev.platform_data; + + hwmon = kzalloc(sizeof(struct nsa3xx_hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + platform_set_drvdata(pdev, hwmon); + hwmon->pdev = pdev; + hwmon->mcu_data = 0; + mutex_init(&hwmon->update_lock); + + ret = sysfs_create_group(&pdev->dev.kobj, &nsa3xx_attr_group); + if (ret) + goto err; + + hwmon->classdev = hwmon_device_register(&pdev->dev); + if (IS_ERR(hwmon->classdev)) { + ret = PTR_ERR(hwmon->classdev); + goto err_sysfs; + } + + ret = nsa3xx_hwmon_request_gpios(pdata); + if (ret) + goto err_free_gpio; + + dev_info(&pdev->dev, "initialized\n"); + + return 0; + +err_free_gpio: + nsa3xx_hwmon_free_gpios(pdata); + hwmon_device_unregister(hwmon->classdev); +err_sysfs: + sysfs_remove_group(&pdev->dev.kobj, &nsa3xx_attr_group); +err: + platform_set_drvdata(pdev, NULL); + kfree(hwmon); + return ret; +} + +static int __devexit nsa3xx_hwmon_remove(struct platform_device *pdev) +{ + struct nsa3xx_hwmon *hwmon = platform_get_drvdata(pdev); + + nsa3xx_hwmon_free_gpios(pdev->dev.platform_data); + hwmon_device_unregister(hwmon->classdev); + sysfs_remove_group(&pdev->dev.kobj, &nsa3xx_attr_group); + platform_set_drvdata(pdev, NULL); + kfree(hwmon); + + return 0; +} + +static struct platform_driver nsa3xx_hwmon_driver = { + .probe = nsa3xx_hwmon_probe, + .remove = __devexit_p(nsa3xx_hwmon_remove), + .driver = { + .name = "nsa3xx-hwmon", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(nsa3xx_hwmon_driver); + +MODULE_AUTHOR("Peter Schildmann "); +MODULE_DESCRIPTION("NSA3XX Hardware Monitoring"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:nsa3xx-hwmon"); diff -ruN a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c --- a/drivers/mmc/core/core.c 2012-10-07 11:41:28.000000000 -0400 +++ b/drivers/mmc/core/core.c 2012-10-10 13:37:18.000000000 -0400 @@ -546,7 +546,7 @@ */ limit_us = 3000000; else - limit_us = 100000; + limit_us = 200000; /* * SDHC cards always use these fixed values. diff -ruN a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c --- a/drivers/mmc/core/sd.c 2012-10-07 11:41:28.000000000 -0400 +++ b/drivers/mmc/core/sd.c 2012-10-10 13:37:18.000000000 -0400 @@ -355,6 +355,15 @@ return -ENOMEM; } + /* + * Some SDHC cards, notably those with a Sandisk SD controller + * (also found in Kingston products) need a bit of slack + * before successfully handling the SWITCH command. So far, + * cards identifying themselves as "SD04G" and "SD08G" are + * affected + */ + udelay(100); + err = mmc_sd_switch(card, 1, 0, 1, status); if (err) goto out; diff -ruN a/drivers/mmc/host/mvsdio.c b/drivers/mmc/host/mvsdio.c --- a/drivers/mmc/host/mvsdio.c 2012-10-07 11:41:28.000000000 -0400 +++ b/drivers/mmc/host/mvsdio.c 2012-10-10 13:37:18.000000000 -0400 @@ -22,6 +22,7 @@ #include #include #include +#include #include #include @@ -150,6 +151,7 @@ dev_dbg(host->dev, "cmd %d (hw state 0x%04x)\n", cmd->opcode, mvsd_read(MVSD_HW_STATE)); + if (cmd->opcode == SD_SWITCH) mdelay(1); /* Voodoo */ cmdreg = MVSD_CMD_INDEX(cmd->opcode); diff -ruN a/include/linux/nsa3xx-hwmon.h b/include/linux/nsa3xx-hwmon.h --- a/include/linux/nsa3xx-hwmon.h 1969-12-31 19:00:00.000000000 -0500 +++ b/include/linux/nsa3xx-hwmon.h 2012-10-10 13:37:18.000000000 -0400 @@ -0,0 +1,21 @@ +/* + * include/linux/nsa3xx.hwmon.h + * + * Platform data structure for ZyXEL NSA3xx hwmon driver + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __LINUX_NSA3XX_HWMON_H +#define __LINUX_NSA3XX_HWMON_H + +struct nsa3xx_hwmon_platform_data { + /* GPIO pins */ + unsigned act_pin; + unsigned clk_pin; + unsigned data_pin; +}; + +#endif /* __LINUX_NSA3XX_HWMON_H */