#
# /etc/rc.conf - Main Configuration for Arch Linux ARM
#

# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
#   in the hardware clock being left untouched (useful for virtualization)
#   Note: Using "localtime" is discouraged.
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
# VERBOSE: Verbose level (from 1 to 8). man 3 syslog for level info
#
LOCALE="en_US.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="America/Chicago"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
VERBOSE="3"

# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
#   Replace every !module by an entry as on the following line in a file in
#   /etc/modprobe.d:
#     blacklist module
#   See "man modprobe.conf" for details.
#
MODULES=()

# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30

# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"

# Scan for BTRFS volumes at startup
USEBTRFS="no"

# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="alarm"

# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
#
# Wired network setup
#   - interface: name of device (required)
#   - address: IP address (leave blank for DHCP)
#   - netmask: subnet mask (ignored for DHCP)
#   - gateway: default route (ignored for DHCP)
#
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# gateway=192.168.0.1
#
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=

interface=
address=
netmask=
gateway=

# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"

# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This requires the netcfg package
#
#NETWORKS=(main)

# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
#
DAEMONS=(hwclock syslog-ng network netfs crond sshd)