mirror of
https://github.com/archlinuxarm/PKGBUILDs.git
synced 2024-11-28 22:57:37 +00:00
198 lines
7.4 KiB
Text
198 lines
7.4 KiB
Text
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
# Params:
|
|
# i2c_arm Set to "on" to enable the ARM's i2c interface
|
|
# (default "off")
|
|
# i2c_vc Set to "on" to enable the i2c interface
|
|
# usually reserved for the VideoCore processor
|
|
# (default "off")
|
|
# i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
|
|
# (default "100000")
|
|
# i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
|
|
# (default "100000")
|
|
# i2c_baudrate An alias for i2c_arm_baudrate
|
|
# i2s Set to "on" to enable the i2s interface
|
|
# (default "off")
|
|
# spi Set to "on" to enable the spi interfaces
|
|
# (default "off")
|
|
# act_led_trigger Choose which activity the LED tracks.
|
|
# Use "heartbeat" for a nice load indicator.
|
|
# (default "mmc")
|
|
# act_led_activelow Set to "on" to invert the sense of the LED
|
|
# (default "off")
|
|
# act_led_gpio Set which GPIO pin to use for the activity LED
|
|
# (in case you want to connect it to an external
|
|
# device)
|
|
# (default "16" on a non-Plus board, "47" on a
|
|
# Plus or Pi 2)
|
|
# pwr_led_trigger
|
|
# pwr_led_activelow
|
|
# pwr_led_gpio
|
|
# As for act_led_*, but using the PWR LED.
|
|
# Not available on Model A/B boards.
|
|
# N.B. It is recommended to only enable those interfaces that are needed.
|
|
# Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
|
|
# interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.)
|
|
# Note also that i2c, i2c_arm and i2c_vc are aliases for the physical
|
|
# interfaces i2c0 and i2c1. Use of the numeric variants is still possible
|
|
# but deprecated because the ARM/VC assignments differ between board
|
|
# revisions. The same board-specific mapping applies to i2c_baudrate,
|
|
# and the other i2c baudrate parameters.
|
|
|
|
#device_tree_param=i2c_arm=on
|
|
#device_tree_param=i2c_vc=on
|
|
#device_tree_param=i2s=on
|
|
#device_tree_param=spi=on
|
|
#device_tree_param=act_led_trigger=mmc
|
|
|
|
# Uncomment one of these lines to enable an audio interface
|
|
#device_tree_overlay=hifiberry-dac
|
|
#device_tree_overlay=hifiberry-dacplus
|
|
#device_tree_overlay=hifiberry-digi
|
|
#device_tree_overlay=hifiberry-amp
|
|
#device_tree_overlay=iqaudio-dac
|
|
#device_tree_overlay=iqaudio-dacplus
|
|
|
|
# Uncomment to enable the lirc-rpi module
|
|
# Params: gpio_out_pin GPIO pin for output (default "17")
|
|
# gpio_in_pin GPIO pin for input (default "18")
|
|
# gpio_in_pull Pull up/down/off on the input pin
|
|
# (default "down")
|
|
# sense Override the IR receive auto-detection logic:
|
|
# "1" = force active high
|
|
# "0" = force active low
|
|
# "-1" = use auto-detection
|
|
# (default "-1")
|
|
# softcarrier Turn the software carrier "on" or "off"
|
|
# (default "on")
|
|
# invert "on" = invert the output pin (default "off")
|
|
# debug "on" = enable additional debug messages
|
|
# (default "off")
|
|
#device_tree_overlay=lirc-rpi
|
|
#device_tree_param=gpio_out_pin=17
|
|
#device_tree_param=gpio_in_pin=18
|
|
#device_tree_param=gpio_in_pull=down
|
|
|
|
# Uncomment to enable the w1-gpio Onewire interface module
|
|
# Use this overlay if you *don't* need a pin to drive an external pullup.
|
|
# Params: gpiopin GPIO pin for I/O (default "4")
|
|
# pullup Non-zero, "on", or "y" to enable the parasitic
|
|
# power (2-wire, power-on-data) feature
|
|
#device_tree_overlay=w1-gpio
|
|
#device_tree_param=gpiopin=4
|
|
#device_tree_param=pullup=on
|
|
|
|
# Uncomment to enable the w1-gpio Onewire interface module
|
|
# Use this overlay if you *do* need a pin to drive an external pullup.
|
|
# Params: gpiopin GPIO pin for I/O (default "4")
|
|
# pullup Non-zero, "on", or "y" to enable the parasitic
|
|
# power (2-wire, power-on-data) feature
|
|
# extpullup GPIO pin for external pullup (default "5")
|
|
#device_tree_overlay=w1-gpio-pullup
|
|
#device_tree_param=gpiopin=4
|
|
#device_tree_param=pullup=on
|
|
#device_tree_param=extpullup=5
|
|
|
|
# Uncomment to enable pps-gpio (pulse-per-second time signal via GPIO)
|
|
# Params: gpiopin GPIO input pin (default "18")
|
|
#device_tree_overlay=pps-gpio
|
|
#device_tree_param=gpiopin=18
|
|
|
|
# Uncomment to enable a generic I2C RTC overlay supporting ds1307, ds3231, pcf2127, and pcf8523
|
|
#device_tree_overlay=i2c-rtc
|
|
#device_tree_param=ds1307
|
|
#device_tree_param=ds3231
|
|
#device_tree_param=pcf2127
|
|
#device_tree_param=pcf8523
|
|
|
|
# Uncomment to enable the BMP085/BMP180 temperature/pressure sensor
|
|
#device_tree_overlay=bmp085_i2c-sensor
|
|
|
|
# Uncomment to enable an FB TFT module
|
|
#device_tree_overlay=hy28a
|
|
#device_tree_overlay=hy28b
|
|
#device_tree_overlay=piscreen
|
|
#device_tree_overlay=rpi-display
|
|
#device_tree_overlay=pitft28-resistive
|
|
#device_tree_overlay=mz61581
|
|
|
|
# Uncomment to enable the Microchip ENC28J60 Ethernet Controller
|
|
#device_tree_overlay=enc28j60
|
|
|
|
# Uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# Uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# Uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# Uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# Uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# Uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# Uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# Uncomment to set monitor mode to DMT
|
|
#hdmi_group=2
|
|
|
|
# Uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# Uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
# Uncomment to overclock the ARM core. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# for more options see http://elinux.org/RPi_config.txt
|
|
|
|
## Some over clocking settings, governor already set to ondemand
|
|
|
|
##None
|
|
#arm_freq=700
|
|
#core_freq=250
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Modest
|
|
#arm_freq=800
|
|
#core_freq=300
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Medium
|
|
#arm_freq=900
|
|
#core_freq=333
|
|
#sdram_freq=450
|
|
#over_voltage=2
|
|
|
|
##High
|
|
#arm_freq=950
|
|
#core_freq=450
|
|
#sdram_freq=450
|
|
#over_voltage=6
|
|
|
|
##Turbo
|
|
#arm_freq=1000
|
|
#core_freq=500
|
|
#sdram_freq=500
|
|
#over_voltage=6
|
|
|
|
gpu_mem=64
|