mirror of
https://github.com/archlinuxarm/PKGBUILDs.git
synced 2024-11-28 22:57:37 +00:00
159 lines
5.5 KiB
Text
159 lines
5.5 KiB
Text
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
# Params:
|
|
# i2c_arm (default "off") Set to "on" to enable the ARM's i2c interface
|
|
# i2c_vc (default "off") Set to "on" to enable the i2c interface
|
|
# usually reserved for the VideoCore processor
|
|
# i2c An alias for i2c_arm
|
|
# i2s (default "off") Set to "on" to enable the i2s interface
|
|
# spi (default "off") Set to "on" to enable the spi interfaces
|
|
# act_led_trigger (default "mmc")
|
|
# Choose which activity the LED tracks.
|
|
# Use "heartbeat" for a nice load indicator.
|
|
# act_led_activelow (default "off")
|
|
# Set to "on" to invert the sense of the LED
|
|
# act_led_gpio (default "16" on a non-Plus board, "47" on a Plus)
|
|
# Set which GPIO pin to use for the activity LED
|
|
# (in case you want to connect it to an external
|
|
# device).
|
|
#
|
|
# N.B. It is recommended to only enable those interfaces that are needed.
|
|
# Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
|
|
# interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.)
|
|
# Note also that i2c_arm and i2c_vc are aliases for the physical
|
|
# interfaces i2c0 and i2c1. Use of the numeric variants is still possible
|
|
# but deprecated because the ARM/VC assignments differ between board
|
|
# revisions.
|
|
#device_tree_param=i2c_arm=on
|
|
#device_tree_param=i2c_vc=on
|
|
#device_tree_param=i2s=on
|
|
#device_tree_param=spi=on
|
|
#device_tree_param=act_led_trigger=mmc
|
|
|
|
# Uncomment one of these lines to enable an audio interface
|
|
#device_tree_overlay=hifiberry-dac
|
|
#device_tree_overlay=hifiberry-dacplus
|
|
#device_tree_overlay=hifiberry-digi
|
|
#device_tree_overlay=hifiberry-amp
|
|
#device_tree_overlay=iqaudio-dac
|
|
#device_tree_overlay=iqaudio-dacplus
|
|
|
|
# Uncomment to enable the lirc-rpi module
|
|
# Params: gpio_out_pin (default "17") GPIO pin for output
|
|
# gpio_in_pin (default "18") GPIO pin for input
|
|
# gpio_in_pull (default "down") Pull up/down/off on the input pin
|
|
# sense (defaults to "-1") Override the IR receive auto-detection
|
|
# logic:
|
|
# "1" = force active high
|
|
# "0" = force active low
|
|
# "-1" = use auto-detection
|
|
# softcarrier (default "on") Turn the software carrier "on" or "off".
|
|
# invert (default "off") "on" = invert the output pin.
|
|
# debug (default "off") "on" = enable additional debug messages.
|
|
#device_tree_overlay=lirc-rpi
|
|
#device_tree_param=gpio_out_pin=17
|
|
#device_tree_param=gpio_in_pin=18
|
|
#device_tree_param=gpio_in_pull=down
|
|
|
|
# Uncomment to enable the w1-gpio Onewire interface module
|
|
# Use this overlay if you *don't* need a pin to drive an external pullup
|
|
# N.B. The parasitic power feature is not yet functional using DT.
|
|
# Params: gpiopin (default "4") GPIO pin for I/O
|
|
#device_tree_overlay=w1-gpio
|
|
#device_tree_param=gpiopin=4
|
|
|
|
# Uncomment to enable the w1-gpio Onewire interface module
|
|
# Use this overlay if you *do* need a pin to drive an external pullup
|
|
# N.B. The parasitic power feature is not yet functional using DT.
|
|
# Params: gpiopin (default "4") GPIO pin for I/O
|
|
# pullup (default "5") GPIO pin for external pullup
|
|
#device_tree_overlay=w1-gpio
|
|
#device_tree_param=gpiopin=4
|
|
#device_tree_param=pullup=5
|
|
|
|
# Uncomment to enable pps-gpio (pulse-per-second time signal via GPIO)
|
|
# Params: gpiopin (default "18") GPIO input pin
|
|
#device_tree_overlay=pps-gpio
|
|
#device_tree_param=gpiopin=18
|
|
|
|
# Uncomment to enable pfc8523 Real Time Clock
|
|
#device_tree_overlay=pfc8523-rtc
|
|
|
|
# Uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# Uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# Uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# Uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# Uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# Uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# Uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# Uncomment to set monitor mode to DMT
|
|
#hdmi_group=2
|
|
|
|
# Uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# Uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
# Uncomment to overclock the ARM core. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# for more options see http://elinux.org/RPi_config.txt
|
|
|
|
## Some over clocking settings, governor already set to ondemand
|
|
|
|
##None
|
|
#arm_freq=700
|
|
#core_freq=250
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Modest
|
|
#arm_freq=800
|
|
#core_freq=300
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Medium
|
|
#arm_freq=900
|
|
#core_freq=333
|
|
#sdram_freq=450
|
|
#over_voltage=2
|
|
|
|
##High
|
|
#arm_freq=950
|
|
#core_freq=450
|
|
#sdram_freq=450
|
|
#over_voltage=6
|
|
|
|
##Turbo
|
|
#arm_freq=1000
|
|
#core_freq=500
|
|
#sdram_freq=500
|
|
#over_voltage=6
|
|
|
|
gpu_mem_512=64
|
|
gpu_mem_256=64
|