mirror of
https://github.com/archlinuxarm/PKGBUILDs.git
synced 2024-11-18 22:54:00 +00:00
129 lines
4.3 KiB
Text
129 lines
4.3 KiB
Text
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
# Params:
|
|
# i2c_arm Set to "on" to enable the ARM's i2c interface
|
|
# (default "off")
|
|
# i2c_vc Set to "on" to enable the i2c interface
|
|
# usually reserved for the VideoCore processor
|
|
# (default "off")
|
|
# i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
|
|
# (default "100000")
|
|
# i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
|
|
# (default "100000")
|
|
# i2c_baudrate An alias for i2c_arm_baudrate
|
|
# i2s Set to "on" to enable the i2s interface
|
|
# (default "off")
|
|
# spi Set to "on" to enable the spi interfaces
|
|
# (default "off")
|
|
# act_led_trigger Choose which activity the LED tracks.
|
|
# Use "heartbeat" for a nice load indicator.
|
|
# (default "mmc")
|
|
# act_led_activelow Set to "on" to invert the sense of the LED
|
|
# (default "off")
|
|
# act_led_gpio Set which GPIO pin to use for the activity LED
|
|
# (in case you want to connect it to an external
|
|
# device)
|
|
# (default "16" on a non-Plus board, "47" on a
|
|
# Plus or Pi 2)
|
|
# pwr_led_trigger
|
|
# pwr_led_activelow
|
|
# pwr_led_gpio
|
|
# As for act_led_*, but using the PWR LED.
|
|
# Not available on Model A/B boards.
|
|
# N.B. It is recommended to only enable those interfaces that are needed.
|
|
# Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
|
|
# interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.)
|
|
# Note also that i2c, i2c_arm and i2c_vc are aliases for the physical
|
|
# interfaces i2c0 and i2c1. Use of the numeric variants is still possible
|
|
# but deprecated because the ARM/VC assignments differ between board
|
|
# revisions. The same board-specific mapping applies to i2c_baudrate,
|
|
# and the other i2c baudrate parameters.
|
|
|
|
#device_tree_param=i2c_arm=on
|
|
#device_tree_param=i2c_vc=on
|
|
#device_tree_param=i2s=on
|
|
#device_tree_param=spi=on
|
|
#device_tree_param=act_led_trigger=mmc
|
|
|
|
#
|
|
# See /boot/overlays/README for a detailed list and description of additional
|
|
# overlays and their configuration options.
|
|
#
|
|
|
|
# Uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# Uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# Uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# Uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# Uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# Uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# Uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# Uncomment to set monitor mode to DMT
|
|
#hdmi_group=2
|
|
|
|
# Uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# Uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
# Uncomment to overclock the ARM core. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# for more options see http://elinux.org/RPi_config.txt
|
|
|
|
## Some over clocking settings, governor already set to ondemand
|
|
|
|
##None
|
|
#arm_freq=700
|
|
#core_freq=250
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Modest
|
|
#arm_freq=800
|
|
#core_freq=300
|
|
#sdram_freq=400
|
|
#over_voltage=0
|
|
|
|
##Medium
|
|
#arm_freq=900
|
|
#core_freq=333
|
|
#sdram_freq=450
|
|
#over_voltage=2
|
|
|
|
##High
|
|
#arm_freq=950
|
|
#core_freq=450
|
|
#sdram_freq=450
|
|
#over_voltage=6
|
|
|
|
##Turbo
|
|
#arm_freq=1000
|
|
#core_freq=500
|
|
#sdram_freq=500
|
|
#over_voltage=6
|
|
|
|
gpu_mem=64
|