From 95d385b3a93c6a1af22f2d9ba1271dcc0b9702f9 Mon Sep 17 00:00:00 2001
From: openhp <60161126+openhp@users.noreply.github.com>
Date: Mon, 22 Mar 2021 12:47:14 +0000
Subject: [PATCH] Update README.md

---
 README.md | 36 ++++++++++++++++++------------------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/README.md b/README.md
index 25280ab..6e5acb9 100644
--- a/README.md
+++ b/README.md
@@ -204,34 +204,34 @@ Additional sensors, disabled and not used by default:
 | ------------- | ------------- |
 | **StCntd:_seconds_**	| Startup countdown, short-term power loss protection. |
 | **HP_Started**	| Normal start. |
-| **#Thi>Setp.**	| "Hot in" temperature > setpoint, so no reason to start |
-| **#Ts1>Setp.**	| "Ts1" temperature > setpoint, so no reason to start, see **SETPOINT_TS1** option to switch betwees Thi and Ts1 as setpoint sensor |
+| **#Thi>Setp.**	| "Hot in" temperature > setpoint, so no reason to start. |
+| **#Ts1>Setp.**	| "Ts1" temperature > setpoint, so no reason to start, see **SETPOINT_TS1** option to switch betwees Thi and Ts1 as setpoint sensor. |
 | **HWP_OFF**		| Setpoint sensor temperature > setpoint, so after some time (**HOTCIRCLE_STOP_AFTER** option) hot side pump powered off and gone to power saving mode. |
 | **HWP_ON_by_ev**	| Hot side pump started after power saving. See **HOTCIRCLE_START_EVERY** option. |
 | **#HotPrp:_seconds_**	| Hot side pump is on, waiting for T stabilisation. Countdown, seconds. See **HOTCIRCLE_CHECK_PREPARE** option. |
 | **#HotSlp:_seconds_**	| Hot side pump in power save mode (sleeping). Waiting for next startup. Countdown, seconds. See **HOTCIRCLE_START_EVERY** option. |
 | **#HPSlp:_seconds_**"	| Compressor: pause between starts. Countdown, seconds. **MINCYCLE_POWEROFF** option.|			
 | **#CPpStart**		| Cold side pump started. |
-| **#CPp:_seconds_**	| Cold side pumping. Preparing system to start compressor. Countdown, seconds. **COLDCIRCLE_PREPARE** option |
-| **#Tho>Max**		| "Hot out" temperature is too high. See **T_HOT_MAX** option |
-| **#Thi>Max**		| "Hot in" temperature is too high. , see **T_HOT_MAX** option |
-| **#CaseCold**		| Compressor crankcase temperature is too low. Can't start. This situation occurs if the outdoor installation when AC power was lost for a few hours. Wait, while the crankcase heater stabilizing your compressor temperature. See **T_CRANKCASE_MIN** option |
-| **#CaseHot**		| Compressor is still overheated, waiting. See **T_CRANKCASE_MAX** option |
-| **#Tae<RefMin**	| "After evaporator" temperature too low. Preventing cold loop from freezing and protecting suction line from liquid. See **T_COLDREF_MIN** option |
-| **#Tbe<RefMin**	| "Before evaporator" temperature too low. Preventing cold loop from freezing. See **T_COLDREF_MIN** option |
-| **#Tbc>Max**		| "Before condenser" temperatire is too high. Overheat protection. See **T_BEFORE_CONDENSER_MAX** option |
-| **#Tci<ColdMin**	| "Cold in" temperature is too low. Preventing cold loop from freezing. See **T_COLD_MIN** option |
-| **#Tco<ColdMin**	| "Cold out" temperature is too low. Preventing cold loop from freezing. See **T_COLD_MIN** option |
-| **CWP_ON_CoMin**	| Cold side pump started beause cold side temperature is too low, so preventing cold loop freeze, see **T_COLD_MIN** option |
+| **#CPp:_seconds_**	| Cold side pumping. Preparing system to start compressor. Countdown, seconds. **COLDCIRCLE_PREPARE** option. |
+| **#Tho>Max**		| "Hot out" temperature is too high. See **T_HOT_MAX** option. |
+| **#Thi>Max**		| "Hot in" temperature is too high. , see **T_HOT_MAX** option. |
+| **#CaseCold**		| Compressor crankcase temperature is too low. Can't start. This situation occurs if the outdoor installation when AC power was lost for a few hours. Wait, while the crankcase heater stabilizing your compressor temperature. See **T_CRANKCASE_MIN** option. |
+| **#CaseHot**		| Compressor is still overheated, waiting. See **T_CRANKCASE_MAX** option. |
+| **#Tae<RefMin**	| "After evaporator" temperature too low. Preventing cold loop from freezing and protecting suction line from liquid. See **T_COLDREF_MIN** option. |
+| **#Tbe<RefMin**	| "Before evaporator" temperature too low. Preventing cold loop from freezing. See **T_COLDREF_MIN** option. |
+| **#Tbc>Max**		| "Before condenser" temperatire is too high. Overheat protection. See **T_BEFORE_CONDENSER_MAX** option. |
+| **#Tci<ColdMin**	| "Cold in" temperature is too low. Preventing cold loop from freezing. See **T_COLD_MIN** option. |
+| **#Tco<ColdMin**	| "Cold out" temperature is too low. Preventing cold loop from freezing. See **T_COLD_MIN** option. |
+| **CWP_ON_CoMin**	| Cold side pump started beause cold side temperature is too low, so preventing cold loop freeze, see **T_COLD_MIN** option. |
 
 **Additional messages**
 | Message | description |
 | ------------- | ------------- |
-| **OK:Pr.Cold**	| Cold side pressure restored|
-| **OK:Pr.Hot**		| Hot side pressure restored|
-| **OK:E.T.Sens.**	| Temperature sensors restored|
-| **HWP_ON** 		| Hot side pump powered on|
-| **Err:_errorcode_**	| Error code: 1 = temperature sensor error, 2 = Hot side pressure too high  3 = cold side pressure too low|
+| **OK:Pr.Cold**	| Cold side pressure restored. |
+| **OK:Pr.Hot**		| Hot side pressure restored.  |
+| **OK:E.T.Sens.**	| Temperature sensors restored.|
+| **HWP_ON** 		| Hot side pump powered on.    |
+| **Err:_errorcode_**	| Error code: 1 = temperature sensor error, 2 = Hot side pressure too high  3 = cold side pressure too low. |
 
 ##  Appendix C: Firmware options and fine tunings