[VictoriaLogs](https://docs.victoriametrics.com/victorialogs/) can accept logs in [Syslog formats](https://en.wikipedia.org/wiki/Syslog) at the specified TCP and UDP addresses
via `-syslog.listenAddr.tcp` and `-syslog.listenAddr.udp` command-line flags. The following syslog formats are supported:
For example, the following command starts VictoriaLogs, which accepts logs in Syslog format at TCP port 514 on all the network interfaces:
```sh
./victoria-logs -syslog.listenAddr.tcp=:514
```
It may be needed to run VictoriaLogs under `root` user or to set [`CAP_NET_BIND_SERVICE`](https://superuser.com/questions/710253/allow-non-root-process-to-bind-to-port-80-and-443)
option if syslog messages must be accepted at TCP port below 1024.
The following command starts VictoriaLogs, which accepts logs in Syslog format at TCP and UDP ports 514:
- [`_msg`](https://docs.victoriametrics.com/victorialogs/keyconcepts/#message-field) - the `MESSAGE` field from the supported syslog formats above
-`hostname`, `app_name` and `proc_id` - [stream fields](https://docs.victoriametrics.com/victorialogs/keyconcepts/#stream-fields) for unique identification
over every log stream
-`priority`, `factility` and `severity` - these fields are extracted from `<PRI>` field
-`format` - this field is set to either `rfc3164` or `rfc5424` depending on the format of the parsed syslog line
-`msg_id` - `MSGID` field from log line in `RFC5424` format.
By default local timezone is used when parsing timestamps in `rfc3164` lines. This can be changed to any desired timezone via `-syslog.timezone` command-line flag.
See [the list of supported timezone identifiers](https://en.wikipedia.org/wiki/List_of_tz_database_time_zones). For example, the following command starts VictoriaLogs,
which parses syslog timestamps in `rfc3164` using `Europe/Berlin` timezone:
By default, the ingested logs are stored in the `(AccountID=0, ProjectID=0)` [tenant](https://docs.victoriametrics.com/victorialogs/#multitenancy).
If you need storing logs in other tenant, then specify the needed tenant via `-syslog.tenantID` command-line flag.
For example, the following command starts VictoriaLogs, which writes syslog messages received at TCP port 514, to `(AccountID=12, ProjectID=34)` tenant:
1. Run VictoriaLogs with `-syslog.listenAddr.tcp=:29514` command-line flag.
1. Put the following line to [rsyslog](https://www.rsyslog.com/) config (this config is usually located at `/etc/rsyslog.conf`):
```
*.* @@victoria-logs-server:29514
```
Where `victoria-logs-server` is the hostname where VictoriaLogs runs. See [these docs](https://www.rsyslog.com/sending-messages-to-a-remote-syslog-server/)
for more details.
## Syslog-ng
1. Run VictoriaLogs with `-syslog.listenAddr.tcp=:29514` command-line flag.
1. Put the following line to [syslog-ng](https://www.syslog-ng.com/) config:
```
destination d_remote {
tcp("victoria-logs-server" port(29514));
};
```
Where `victoria-logs-server` is the hostname where VictoriaLogs runs.
See [these docs](https://www.syslog-ng.com/technical-documents/doc/syslog-ng-open-source-edition/3.19/administration-guide/29#TOPIC-1094570) for details.
