mirror of
https://github.com/uhi22/pyPLC.git
synced 2024-09-11 00:38:29 +00:00
56 lines
2.5 KiB
INI
56 lines
2.5 KiB
INI
|
|
||
|
|
[general]
|
||
|
|
# mode can be either PevMode to use as car, or EvseMode to use as charger
|
||
|
|
mode = PevMode
|
||
|
|
|
||
|
|
# Simulation without modem
|
||
|
|
# For development purposes, make it possible to run two instances (pev and evse) on one machine, without
|
||
|
|
# a modem connected. This feature is not tested since a long time, most likely does not work as intended.
|
||
|
|
# todo: replace isSimulationMode by this setting
|
||
|
|
is_simulation_without_modems = false
|
||
|
|
|
||
|
|
# The Ethernet interface. Usually eth0 on Raspberry.
|
||
|
|
# Todo: This setting is considered only on linux. Find a clean solution for windows is to be done.
|
||
|
|
eth_interface = eth0
|
||
|
|
|
||
|
|
# If a display is connected via serial line, e.g. an WIFI-KIT-32 running the software from https://github.com/uhi22/SerialToOLED
|
||
|
|
display_via_serial = yes
|
||
|
|
|
||
|
|
# LightBulbDemo turns on the relay with a short delay in the charging loop, to stabilize the voltage
|
||
|
|
# before the resistive load is connected.
|
||
|
|
light_bulb_demo = yes
|
||
|
|
|
||
|
|
# SOC simulation.
|
||
|
|
# In PevMode, simulate a rising SOC while charging.
|
||
|
|
soc_simulation = yes
|
||
|
|
|
||
|
|
# Device selection for the digital outputs, for CP state and power relays
|
||
|
|
# Possible options:
|
||
|
|
# dieter: Serial controlled device, which controls the digital outputs. E.g. arduino from https://github.com/uhi22/dieter
|
||
|
|
# beaglebone: GPIO pins of the beagleBone, as used in https://github.com/jsphuebner/pyPLC/tree/beaglebone
|
||
|
|
digital_output_device = dieter
|
||
|
|
#digital_output_device = beaglebone
|
||
|
|
|
||
|
|
# Device to read the physically measured inlet voltage in PevMode
|
||
|
|
# Either the high-voltage dieter from https://github.com/uhi22/dieter, which is connected on serial port.
|
||
|
|
# Or "none", if no measurement is intended.
|
||
|
|
#analog_input_device = dieter
|
||
|
|
analog_input_device = none
|
||
|
|
|
||
|
|
# Criteria for ending the PreCharge phase in PevMode
|
||
|
|
# Possible options:
|
||
|
|
# yes: use the EVSEPresentVoltage which is reported by the charger, to decide the end of the precharge
|
||
|
|
# no: use the physically measured inlet voltage to decide the end of the precharge
|
||
|
|
use_evsepresentvoltage_for_precharge_end = yes
|
||
|
|
|
||
|
|
# Use the physically measured inlet voltage to show on display during the charge loop.
|
||
|
|
# If false, we are showing the EVSEPresentVoltage which is reported by the charger.
|
||
|
|
use_physical_inlet_voltage_during_chargeloop = no
|
||
|
|
|
||
|
|
# Voltage threshold for the end-of-precharge decision
|
||
|
|
# This is the maximum difference voltage between the charger voltage and the accu voltage. If the actual voltage
|
||
|
|
# difference is lower than this threshold, we will close the power relay, to connect the accu to the charger.
|
||
|
|
# Unit: volt
|
||
|
|
u_delta_max_for_end_of_precharge = 10
|
||
|
|
|