configurable MAC logging and configurable ignoring missing modem. Docu preparation for GPS logging

addressManager.py

@@ -122,10 +122,12 @@ class addressManager():
         if (len(self.localIpv6Addresses)==0):
             print("[addressManager] Error: No local Ipv6 address was found.")
             self.localIpv6Address = "localhost"
-            cfg_exitIfNoLocalLinkAddressIsFound = 1
+            cfg_exitIfNoLocalLinkAddressIsFound = getConfigValueBool("exit_if_no_local_link_address_is_found")
             if (cfg_exitIfNoLocalLinkAddressIsFound!=0):
-                print("Exiting, because it does not make sense to continue without IPv6 address");
+                print("Exiting, because it does not make sense to continue without IPv6 address")
-                sys.exit(1);
+                sys.exit(1)
+            else:
+                print("Error: It does not make sense to continue without IPv6 address, but exit_if_no_local_link_address_is_found says you want to continue");
         else:
             # at least one address was found. Take the first one (this may be the wrong adaptor).
             self.localIpv6Address = self.localIpv6Addresses[0]

doc/installation_on_raspberry.md

@@ -241,3 +241,23 @@ https://strobelstefan.org/2019/10/16/zugriff-via-ssh-ohne-passworteingabe-anmeld
 - in connection->SSH->Auth, browse to the private key generated above.
 - in session, give a name for the session, and click "safe" to store the connection settings
 - next time, the connection to the pi works just by clicking the saved session.
+
+## Optional: MAC logging with GPS coordinates
+
+0. connect GPS module to the raspberry. This needs only 3 wires: 3V3, GND, RXD. The TXD of the module needs to be connected to the RXD of the raspberry. https://tutorials-raspberrypi.de/raspberry-pi-gps-ortung-navigation/
+1. `sudo apt-get install minicom gpsd gpsd-clients`
+2. in the raspberry pi config, enable the serial port and disable the serial console
+3. reboot
+4. `ls -ltr /dev/ser* # should show all serial devices`
+5. `cat /dev/serial0` Get the the raw NMEA data from the serial line and shows it. Processing of them works also without the daemon.
+6. configure the gsd: `nano /etc/default/gpsd`
+
+```
+    USBAUTO=“false“
+    DEVICES=“/dev/serial0″
+    GPSD_OPTIONS=“-n“
+```
+
+start the GPS daemon: `sudo service gpsd start`
+
+Now this works: `cgps -s`

doc/pyPlc.ini.template

@@ -103,6 +103,16 @@ charge_target_voltage = 270
 # Deeper explanations here: https://github.com/uhi22/pyPLC/blob/master/doc/installation_on_raspberry.md#further-optimizations
 exit_on_session_end = False
 
+# If pyPLC does not find a local link address, this means there is no
+# ethernet connection to the homeplug modem. This is a severe hardware
+# error, so pyPLC will terminate. However, for special testing purposes this can
+# be set to False. In this case, pyPLC will continue to run, even if there is no modem connected.
+exit_if_no_local_link_address_is_found = True
+
+# pyPLC in PevMode or ListenMode can detect the MAC address of the charger (SECC MAC) and 
+# write it, together with the time stamp, into the file MacLog.txt
+log_the_evse_mac_to_file = True
+
 # Run test cases.
 # Explanation in doc/testing_and_simulation.md
 # Possible values:
@@ -125,7 +135,7 @@ udp_syslog_enable = Yes
 #           Limitations/explanations here: https://openinverter.org/forum/viewtopic.php?p=57894#p57894 and
 #           https://openinverter.org/forum/viewtopic.php?t=1063 (Is it possible to make a CCS to CHAdeMO adapter?)
 #  none: all other use cases
-charge_parameter_backend = chademo
+charge_parameter_backend = none
 
 # REST callback for SoC states. Comment out to disable. Do not leave a trailing slash
 # This parameter is used in EvseMode, to configure where the data which is retrieved

pyPlcHomeplug.py

@@ -710,12 +710,14 @@ class pyPlcHomeplug():
             if (self.pevSequenceState==STATE_WAITING_FOR_SLAC_PARAM_CNF): # we were waiting for the SlacParamCnf
                 self.pevSequenceDelayCycles = 4 # original Ioniq is waiting 200ms
                 self.enterState(STATE_SLAC_PARAM_CNF_RECEIVED) # enter next state. Will be handled in the cyclic runPevSequencer
-        if (self.iAmListener==1):
+        if ((self.iAmListener==1) or (self.iAmPev==1)):
-            self.addToTrace("SECC MAC is " + self.getSourceMacAddressAsString())
+            if getConfigValueBool("log_the_evse_mac_to_file"):
-            strDateTime=datetime.today().strftime('%Y-%m-%dT%H:%M:%S.%f')
+                # Write the MAC address of the charger to a log file
-            MacLogFile = open('MacLog.txt', 'a')
+                self.addToTrace("SECC MAC is " + self.getSourceMacAddressAsString())
-            MacLogFile.write(strDateTime + " SECC MAC " + self.getSourceMacAddressAsString() + "\n") # write the MAC to the MacLogFile
+                strDateTime=datetime.today().strftime('%Y-%m-%dT%H:%M:%S.%f')
-            MacLogFile.close()
+                MacLogFile = open('MacLog.txt', 'a')
+                MacLogFile.write(strDateTime + " SECC MAC " + self.getSourceMacAddressAsString() + "\n") # write the MAC to the MacLogFile
+                MacLogFile.close()
             
     def evaluateMnbcSoundInd(self):
         # We received MNBC_SOUND.IND from the PEV. Normally this happens 10times, with a countdown (remaining number of sounds)