mirror of
https://github.com/uhi22/pyPLC.git
synced 2024-12-20 01:31:52 +00:00
150 lines
6.7 KiB
Text
150 lines
6.7 KiB
Text
# This is the template file pyPlc.ini.template.
|
|
# Copy this file in the same folder like the pyPlc.py, and rename it to pyPlc.ini
|
|
|
|
[general]
|
|
# mode can be either PevMode to use as car, or EvseMode to use as charger.
|
|
# This setting can be overruled by using the first command line parameter, to EvseMode:
|
|
# python pyPlc.py E
|
|
# or to PevMode:
|
|
# python pyPlc.py P
|
|
mode = PevMode
|
|
|
|
# Simulation without modem
|
|
# For development purposes, make it possible to run two instances (pev and evse) on one machine, without
|
|
# a modem connected.
|
|
# If this setting is set to false, nevertheless the simulation mode can be activated by the second command
|
|
# line parameter "S", e.g.
|
|
# python pyPlc.py E S
|
|
# or
|
|
# python pyPlc.py P S
|
|
is_simulation_without_modems = false
|
|
|
|
# The Ethernet interface. Usually eth0 on Raspberry.
|
|
# This setting is considered only on linux.
|
|
eth_interface = eth0
|
|
|
|
# The Ethernet interface name on Windows. Something like
|
|
# \Device\NPF_{E4B8176C-8516-4D48-88BC-85225ABCF259}
|
|
eth_windows_interface_name = \Device\NPF_{E4B8176C-8516-4D48-88BC-85225ABCF259}
|
|
|
|
# If a display is connected via serial line, e.g. an WIFI-KIT-32 running the software from https://github.com/uhi22/SerialToOLED
|
|
# Possible values: yes or no
|
|
display_via_serial = yes
|
|
|
|
# LightBulbDemo turns on the relay with a short delay in the charging loop, to stabilize the voltage
|
|
# before the resistive load is connected.
|
|
# This mode is intended to test the PevMode without the need of a real battery, but a load like a light bulb,
|
|
# or kettle or similar.
|
|
# Possible values: yes or no
|
|
# For the use together with a real battery set this to "no".
|
|
light_bulb_demo = no
|
|
|
|
# SOC simulation.
|
|
# In PevMode, simulate a rising SOC while charging.
|
|
# Possible values: yes or no
|
|
soc_simulation = yes
|
|
|
|
# Device selection for the digital outputs, for CP state and power relays
|
|
# Possible options:
|
|
# dieter: Serial controlled device, which controls the digital outputs. E.g. arduino from https://github.com/uhi22/dieter
|
|
# beaglebone: GPIO pins of the beagleBone, as used in https://github.com/jsphuebner/pyPLC/tree/beaglebone
|
|
# celeron55device: Serial controlled device as used in https://openinverter.org/forum/viewtopic.php?p=56192#p56192
|
|
digital_output_device = dieter
|
|
#digital_output_device = beaglebone
|
|
#digital_output_device = celeron55device
|
|
|
|
|
|
# Device to read the physically measured inlet voltage in PevMode
|
|
# Possible options:
|
|
# dieter: The high-voltage dieter from https://github.com/uhi22/dieter, which is connected on serial port.
|
|
# none: if no measurement is intended.
|
|
# celeron55device: as used in https://openinverter.org/forum/viewtopic.php?p=56192#p56192
|
|
#analog_input_device = dieter
|
|
analog_input_device = none
|
|
#analog_input_device = celeron55device
|
|
|
|
|
|
# Criteria for ending the PreCharge phase in PevMode
|
|
# Possible options:
|
|
# yes: use the EVSEPresentVoltage which is reported by the charger, to decide the end of the precharge
|
|
# no: use the physically measured inlet voltage to decide the end of the precharge
|
|
use_evsepresentvoltage_for_precharge_end = yes
|
|
|
|
# Use the physically measured inlet voltage to show on display during the charge loop.
|
|
# If false, we are showing the EVSEPresentVoltage which is reported by the charger.
|
|
use_physical_inlet_voltage_during_chargeloop = no
|
|
|
|
# Voltage threshold for the end-of-precharge decision
|
|
# This is the maximum difference voltage between the charger voltage and the accu voltage. If the actual voltage
|
|
# difference is lower than this threshold, we will close the power relay, to connect the accu to the charger.
|
|
# Unit: volt
|
|
u_delta_max_for_end_of_precharge = 10
|
|
|
|
# Added by celeron55
|
|
# The serial port and baud rate used for communication. Used
|
|
# for serial devices like Dieter, OLED-Display and
|
|
# celeron55's measuring and switching device
|
|
# Examples:
|
|
# /dev/ttyS1
|
|
# auto
|
|
serial_port = auto
|
|
serial_baud = 19200
|
|
|
|
# The target voltage used in the CurrentDemandRequest.
|
|
# This is a value for first try-outs. Better would
|
|
# be if the BMS would provide the value.
|
|
# 11 * 6 * 4.1V = 66 * 4.1V = 270V
|
|
charge_target_voltage = 270
|
|
|
|
# By using an external manager script, this is useful for splitting charging
|
|
# into separately logged sessions and avoiding logging when not connected to a
|
|
# charger.
|
|
# Recommended setting: True, and configure the starter.sh as service (Linux only).
|
|
# Deeper explanations here: https://github.com/uhi22/pyPLC/blob/master/doc/installation_on_raspberry.md#further-optimizations
|
|
exit_on_session_end = False
|
|
|
|
# If pyPLC does not find a local link address, this means there is no
|
|
# ethernet connection to the homeplug modem. This is a severe hardware
|
|
# error, so pyPLC will terminate. However, for special testing purposes this can
|
|
# be set to False. In this case, pyPLC will continue to run, even if there is no modem connected.
|
|
exit_if_no_local_link_address_is_found = True
|
|
|
|
# pyPLC in PevMode or ListenMode can detect the MAC address of the charger (SECC MAC) and
|
|
# write it, together with the time stamp, into the file MacLog.txt
|
|
log_the_evse_mac_to_file = True
|
|
|
|
# Run test cases.
|
|
# Explanation in doc/testing_and_simulation.md
|
|
# Possible values:
|
|
# No: No testcases are executed. Normal function as Evse or Pev.
|
|
# Yes: Testcases are executed. The EvseMode will produce various errors for fault injection tests.
|
|
testsuite_enable = No
|
|
|
|
# Logging to UDP Syslog messages
|
|
# If this is activated, the pyPlc will send all logging messages also to the network interface,
|
|
# in form of UDP Syslog messages. For details see in udplog.py.
|
|
# For development purposes, set this to "Yes".
|
|
# For daily use, set this to "No". There is the risk that the broadcast UDP packets disturb the charger,
|
|
# which may lead to unwanted aborts.
|
|
udp_syslog_enable = Yes
|
|
|
|
# Set backend for obtaining charging parameters, we start with CHAdeMO CAN for now
|
|
# Need to make a simulator device and maybe a celeron device?
|
|
# Possible values:
|
|
# chademo: pyPLC is used as bridge between a CCS charger and a CHAdeMO* car.
|
|
# Limitations/explanations here: https://openinverter.org/forum/viewtopic.php?p=57894#p57894 and
|
|
# https://openinverter.org/forum/viewtopic.php?t=1063 (Is it possible to make a CCS to CHAdeMO adapter?)
|
|
# none: all other use cases
|
|
charge_parameter_backend = none
|
|
|
|
# REST callback for SoC states. Comment out to disable. Do not leave a trailing slash
|
|
# This parameter is used in EvseMode, to configure where the data which is retrieved
|
|
# from the vehicle shall go to. Discussed
|
|
# here: https://github.com/SmartEVSE/SmartEVSE-3/issues/25#issuecomment-1563519025
|
|
soc_callback_enabled = False
|
|
soc_callback_endpoint = http://1.1.1.1
|
|
# Fallback value to use if the vehicle does not support the EVEnergyCapacity.Value
|
|
soc_fallback_energy_capacity = 2700
|
|
|
|
# The URL where to send some logging data.
|
|
logging_url = http://enteryourhosthere.org/pyPlcLogging/addLog.php
|