PKGBUILDs/core/linux-armv5-rc/0008-ARM-dts-kirkwood-Initial-support-for-GoFlex-Home.patch

161 lines
4.3 KiB
Diff
Raw Normal View History

2018-04-18 02:07:27 +00:00
From 5684388f6389cddb57a830285965af3c39858249 Mon Sep 17 00:00:00 2001
2018-02-27 01:43:53 +00:00
From: Kevin Mihelich <kevin@archlinuxarm.org>
Date: Sun, 25 Feb 2018 16:42:40 -0700
Subject: [PATCH 8/9] ARM: dts: kirkwood: Initial support for GoFlex Home
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
---
arch/arm/boot/dts/Makefile | 1 +
2018-04-18 02:07:27 +00:00
arch/arm/boot/dts/kirkwood-goflexhome.dts | 127 ++++++++++++++++++++++
2018-02-27 01:43:53 +00:00
2 files changed, 128 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-goflexhome.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
2018-04-18 02:07:27 +00:00
index 67f0410cb961..7b23ace892dc 100644
2018-02-27 01:43:53 +00:00
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
2018-04-18 02:07:27 +00:00
@@ -250,6 +250,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
2018-02-27 01:43:53 +00:00
kirkwood-ds411.dtb \
kirkwood-ds411j.dtb \
kirkwood-ds411slim.dtb \
+ kirkwood-goflexhome.dtb \
kirkwood-goflexnet.dtb \
kirkwood-guruplug-server-plus.dtb \
kirkwood-ib62x0.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-goflexhome.dts b/arch/arm/boot/dts/kirkwood-goflexhome.dts
new file mode 100644
index 000000000000..554716fbf367
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
@@ -0,0 +1,127 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate GoFlex Home";
+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_white: pmx-led_white {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led_orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <1>;
+ };
+
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_orange
+ &pmx_led_green
+ &pmx_led_white
+ >;
+ pinctrl-names = "default";
+
+ health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ misc {
+ label = "status:white:misc";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "sata-disk1";
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x0600000>;
+ };
+
+ partition@0600000 {
+ label = "root";
+ reg = <0x0600000 0xd800000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&eth0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <&ethphy0>;
+ };
+};
--
2018-04-18 02:07:27 +00:00
2.17.0
2018-02-27 01:43:53 +00:00