mirror of
https://github.com/openhp/HeatPumpController.git
synced 2024-11-18 12:33:59 +00:00
Update README.md
This commit is contained in:
openhp
GitHub
parent
1e9c87d106
commit
adf5d7606e
1 changed files with 135 additions and 7 deletions
142
README.md
142
README.md
|
|
@ -59,10 +59,9 @@ Self-test helps you check relays, indicators, speaker and temperature sensors.<b
|
|||
To run a self-tests
|
||||
- uncomment this 3 defines in source code header
|
||||
```c
|
||||
//-----------------------USER OPTIONS-----------------------
|
||||
#define SELFTEST_RELAYS_LEDS_SPEAKER
|
||||
#define SELFTEST_EEV
|
||||
#define SELFTEST_T_SENSORS
|
||||
//#define SELFTEST_RELAYS_LEDS_SPEAKER //speaker and relays QA test, uncomment to enable
|
||||
//#define SELFTEST_EEV //EEV QA test, uncomment to enable
|
||||
//#define SELFTEST_T_SENSORS //temperature sensors QA test, uncomment to enable
|
||||
```
|
||||
- upload firmware
|
||||
- connect 12V power supply<br>
|
||||
|
|
@ -128,9 +127,138 @@ qwer
|
|||
{-desc 2-}
|
||||
qwer
|
||||
|
||||
## Fine tunings
|
||||
{-link to page-}
|
||||
qwer
|
||||
## Firmware options and fine tunings
|
||||
```c
|
||||
//#define SELFTEST_RELAYS_LEDS_SPEAKER //speaker and relays QA test, uncomment to enable
|
||||
//#define SELFTEST_EEV //EEV QA test, uncomment to enable
|
||||
//#define SELFTEST_T_SENSORS //temperature sensors QA test, uncomment to enable
|
||||
|
||||
//communication protocol with external world
|
||||
//#define RS485_JSON 1 //json, external systems integration
|
||||
//#define RS485_HUMAN 2 //RS485 is used in the same way as the local console, warning: Use only if 2 devices (server and this controller) are connected to the same RS485 line
|
||||
#define RS485_MODBUS 3 //default, Modbus via RS485, connection to the display (both sensor or 1602, see https://gitlab.com/valden/) or connection to any other MODBUS application or device
|
||||
|
||||
//system type, comment both if HP with EEV
|
||||
//#define EEV_ONLY //Valden controller as EEV controller: NO target T sensor. No relays. Oly EEV. Sensors required: Tae, Tbe, current sensor. Additional T sensors can be used but not required.
|
||||
//#define NO_EEV //capillary tube or TXV, EEV not used
|
||||
|
||||
//which sensor is used to check setpoint, uncomment one of options
|
||||
#define SETPOINT_THI //"warm floor" scheme: "hot in" (Thi) temperature used as setpoint
|
||||
//#define SETPOINT_TS1 //"swimming pool" or "water tank heater" scheme: "sensor 1" (Ts1) is used as setpoint and located somewhere in water tank
|
||||
|
||||
#define HUMAN_AUTOINFO 30000 //print stats to console, every milliseconds
|
||||
|
||||
#define WATCHDOG //disable for older bootloaders
|
||||
//-----------------------USER OPTIONS END-----------------------
|
||||
|
||||
|
||||
|
||||
//-----------------------Fine Tuning OPTIONS-----------------------
|
||||
//next sections: advanced options
|
||||
|
||||
|
||||
|
||||
//-----------------------T Sensors -----------------------
|
||||
//temperature sensors used in a system, comment to disable
|
||||
#define T_cold_in; //cold side (heat source) inlet sensor
|
||||
#define T_cold_out; //cold side outlet sensor
|
||||
#define T_before_evaporator; //"before" and "after evaporator" sensors are required to control EEV, both "EEV_ONLY" and "full" schemes
|
||||
#define T_after_evaporator; //"before" and "after evaporator" sensors are required to control EEV, both "EEV_ONLY" and "full" schemes
|
||||
//#define T_separator_gas; //no longer used (PCB 1.3 MI +) artifact from experimental scheme with separator
|
||||
//#define T_separator_liquid; //no longer used (PCB 1.3 MI +) artifact from experimental scheme with separator
|
||||
//#define T_before_valve; //no longer used (PCB 1.3 MI +) artifact from experimental scheme with separator
|
||||
//#define T_suction; //no longer used (PCB 1.3 MI +) artifact from experimental scheme with separator
|
||||
#ifdef SETPOINT_TS1
|
||||
#define T_sensor_1; //T values from the additional sensor S1 are used as a "setpoint" in "pool" or "water tank heater" schemes
|
||||
#endif
|
||||
//!!!
|
||||
#define T_sensor_2; //additional sensor, any source, for example: outdoor temperature, in-case temperature, and so on
|
||||
#define T_crc; //if defined: enables crankcase T sensor and crankcase heater on relay 4
|
||||
//#define T_regenerator; //an additional sensor, the regenerator temperature sensor (inlet or outlet or housing) is used only to obtain a temperature data if necessary
|
||||
#define T_afrer_condenser; //after condenser (and before valve)
|
||||
//!!!#define T_before_condenser; //before condenser (discharge)
|
||||
#define T_hot_out; //hot side outlet
|
||||
//in full scheme Hot IN required! optional in "EEV_ONLY" scheme (see "EEV_ONLY" option),
|
||||
#define T_hot_in; //hot side inlet
|
||||
|
||||
//-----------------------TEMPERATURES-----------------------
|
||||
#define MAGIC 0x66; //change this value if you want to rewrite the T setpoint in EEPROM
|
||||
#define T_SETPOINT 26.0; //This is a predefind target temperature value (start temperature). EEPROM-saved. The value can be changed using 1. Console 2. Changing the "setpoint" on a display 3. Changing this value AND changing "magic number"
|
||||
#define T_SETPOINT_MAX 48.0; //maximum "setpoint" temperature that an ordinary user can set
|
||||
#define T_SETPOINT_MIN 10.0; //min. "setpoint" temperature that an ordinary user can set, lower values are not recommended until antifreeze fluids at hot side are used.
|
||||
#define T_CRANKCASE_MIN 8.0; //compressor (crankcase) min. temperature, HP will not start if T lower
|
||||
#define T_CRANKCASE_MAX 110.0; //compressor (crankcase) max. temperature, overheating protection, HP will stop if T higher
|
||||
#define T_CRANKCASE_HEAT_THRESHOLD 16.0; //crankcase heater threshold: heater will be powered on if T lower
|
||||
#define T_WORKINGOK_CRANKCASE_MIN 25.0; //compressor temperature: additional check. HP will stop if T is lower than this value after 5 minutes of work. Do not set the value too large to ensure normal operation after long pauses.
|
||||
#define T_BEFORE_CONDENSER_MAX 108.0; //discharge MAX, system stops if discharge higher
|
||||
#define T_COLDREF_MIN -14.0; //suction min., HP stops if T lower, cold side (glycol) loop freeze protection and compressor protection against liquid
|
||||
#define T_BEFORE_EVAP_WORK_MIN -25.5; //!!!before evaporator (after valve) min. T; can be very low for a few minutes after startup, ex: capillary tube in some conditions; and for all systems: after long shut-off, lack of reagent, 1st starts, and many others
|
||||
#define T_COLD_MIN -15.5; //cold side (glycol) loop freeze protection: HP stops if inlet or outlet temperature lower
|
||||
#define T_HOT_MAX 50.0; //hot loop: HP stops if hot side inlet or outlet temperature higher than this threshold
|
||||
|
||||
//#define T_REG_HEAT_THRESHOLD 17.0; //no longer used (PCB 1.3 MI +) artifact from experimental scheme with separator
|
||||
//#define T_HOTCIRCLE_DELTA_MIN 2.0; //not used since ~FW v1.6, "water heater with intermediate heat exchanger" scheme, where Ts1 == "sensor in water"; hot side CP will be switched on if "Ts1 - hot_out > T_HOTCIRCLE_DELTA_MIN"
|
||||
|
||||
//-----------------------WATTS AND CYCLES TIMES-----------------------
|
||||
//time: milliseconds, power: watts
|
||||
#define MAX_WATTS 1000.0 + 70.0 + 80.0 //power limit, watt, HP stops in case of exceeding, examples: installation1: compressor 165: 920 Watts, + 35 watts 25/4 circ. pump at 1st speed + 53 watts 25/4 circ. pump at 2nd speed
|
||||
// installation2: compressor unk: ~1000 + hot CP 70 + cold CP 80 = 1150 watts
|
||||
// installation3: and so on
|
||||
#define POWERON_PAUSE 300000 //after power on: wait 5 minutes before the start of HP (protected from power faults)
|
||||
#define MINCYCLE_POWEROFF 600000 //after a normal compressor stop: 10 minutes pause (max 99999 seconds)
|
||||
#define MINCYCLE_POWERON 3600000 //after compressor start: minimum compressor operation time, i.e. work time is not less than this value (or more, depending on the setpoint temperature) 60 minutes = 3.6 KK 120mins = 5.4 kK.
|
||||
#define POWERON_HIGHTIME 7000 //after compressor start: defines time when power consumption can be 3 times greater than normal, 7 sec. by default
|
||||
#define COLDCIRCLE_PREPARE 90000 //before compressor start: power on cold CP and wait 90 sec; if false start: CP will off twise this time; and (hotcircle_stop_after - this_value) must be > hotcircle_check_prepare or HP will go sleep cycle instead of start
|
||||
#define DEFFERED_STOP_HOTCIRCLE 1200000 //after compressor stop: wait 20 minutes, if no need to start compressor: stop hot WP; value must be > 0
|
||||
#define HOTCIRCLE_START_EVERY 2400000 //while pauses: pump on "hot side" starts every 40 minutes (by default) (max 9999 seconds) to circulate water and get exact temperature reading , option used if "warm floor" installation (Thi as setpoint)...
|
||||
#define HOTCIRCLE_CHECK_PREPARE 300000 //while pauses: ...and wait temperature stabilisation 5 minutes (by default), after that do setpoint checks...
|
||||
#define HOTCIRCLE_STOP_AFTER (HOTCIRCLE_CHECK_PREPARE + COLDCIRCLE_PREPARE + 30000) //...and then stop after few minutes of circulating, if temperature is high and no need to start compressor; value must be check_prepare + coldcircle_prepare + 30 seconds (or more)
|
||||
|
||||
|
||||
//-----------------------EEV-----------------------
|
||||
//If you are using capillary tube or TXV: simply skip next section
|
||||
//Depending on how many milliseconds are allocated per step, the speed of automatic tuning will change.
|
||||
//Remember that you'll see refrigeration system reaction on every step not immediately, but after few minutes, sometimes after tens of minutes.
|
||||
|
||||
#define EEV_MAXPULSES 250 //max steps, 250 is tested for sanhua 1.3
|
||||
|
||||
//steps tuning: mulliseconds per fast and slow (precise) steps
|
||||
#define EEV_PULSE_FCLOSE_MILLIS 20 //(20 tube evaporator) fast closing, closing on danger (milliseconds per step)
|
||||
#define EEV_PULSE_CLOSE_MILLIS 60000 //(50000 tube evaporator) accurate closing while the compressor works (milliseconds per step)
|
||||
#define EEV_PULSE_WOPEN_MILLIS 20 //(20 tube evaporator) standby (waiting) pos. set (milliseconds per step)
|
||||
#define EEV_PULSE_FOPEN_MILLIS 1400 //(1300 tube evaporator) fast opening, fast search (milliseconds per step)
|
||||
#define EEV_PULSE_OPEN_MILLIS 70000 //(60000 tube evaporator) accurate opening while the compressor works (milliseconds per step)
|
||||
#define EEV_STOP_HOLD 500 //0.1..1sec for Sanhua hold time (milliseconds per step)
|
||||
#define EEV_CLOSEEVERY 86400000 //86400000: EEV will be closed (zero calibration) every 24 hours, executed while HP is NOT working (milliseconds per cycle)
|
||||
|
||||
//positions
|
||||
#define EEV_CLOSE_ADD_PULSES 8 //read below, additional steps after zero position while full closing
|
||||
#define EEV_OPEN_AFTER_CLOSE 45 //0 - set the zero position, then add EEV_CLOSE_ADD_PULSES (zero insurance, read EEV guides for this value) and stop, EEV will be in zero position.
|
||||
//N - set the zero position, than add EEV_CLOSE_ADD_PULSES, than open EEV on EEV_OPEN_AFTER_CLOSE pulses
|
||||
//i.e. it's a "waiting position" while HP not working, value must be <= MINWORKPOS
|
||||
#define EEV_MINWORKPOS 50 //position will be not less during normal work, open EEV to this position after compressor start
|
||||
|
||||
//temperatures
|
||||
#define EEV_PRECISE_START 7.0 //(8.6 tube evaporator) precise tuning threshold: make slower pulses if (real_diff-target_diff) less than this value. Used for fine auto-tuning
|
||||
#define EEV_EMERG_DIFF 1.7 //(2.5 tube evaporator) liquid at suction threshold: if dangerous condition occured: real_diff =< (target_diff - EEV_EMERG_DIFF) then EEV will be closed to min. work position //Ex: EEV_EMERG_DIFF = 2.0, target diff 5.0, if real_diff =< (5.0 - 2.0) then EEV will be closed to EEV_MINWORKPOS
|
||||
#define EEV_HYSTERESIS 0.5 //(0.6 tube evaporator) hysteresis, to stop fine tuning: must be less than EEV_PRECISE_START, ex: target difference = 4.0, hysteresis = 0.3, no EEV pulses will be done while real difference in range 4.0..4.3
|
||||
#define EEV_TARGET_TEMP_DIFF 3.6 //(3.6 tube evaporator) target difference between Before Evaporator and After Evaporator, the head of whole algorithm
|
||||
|
||||
//additional options
|
||||
#define EEV_REOPENLAST 1 //1 = reopen to last position on compressor start, useful for ordinary schemes with everyday working cycles, 0 = not
|
||||
#define EEV_REOPENMINTIME 40000 //after system start: min. delay between "min. work pos." (must be > 0 in this case and > waiting position) set and reopening start
|
||||
//#define EEV_MANUAL //comment to disable, manual set of EEV position via console; warning: this option will stop all EEV auto-activities, including zero position find procedure; so this option not recommended: switching auto/manual mode from console after startup is a better way
|
||||
|
||||
//do not use next option untill you're not really need it
|
||||
//#define EEV_DEBUG //debug, usefull during system fine tuning, works both with local serial and RS485_HUMAN
|
||||
//-----------------------ADDRESSES-----------------------
|
||||
const char devID = 0x45; //used only if JSON communication, does not matter for modbus and Valden display https://github.com/OpenHP/
|
||||
const char hostID = 0x30; //used only if JSON communication, not used for modbus
|
||||
|
||||
//-----------------------OTHER-----------------------
|
||||
#define MAX_SEQUENTIAL_ERRORS 15 //max cycles to wait auto-clean error, ex: T sensor appears, stop compressor after counter exceeded (millis_cycle * MAX_SEQUENTIAL_ERRORS)
|
||||
//-----------------------Fine Tuning OPTIONS END -----------------------
|
||||
```
|
||||
|
||||
## Diagnostic and troubleshooting
|
||||
{-describe messages-}
|
||||
|
|
|
|||
Loading…
Reference in a new issue