### Describe Your Changes
If a dict flag has only one value without a prefix it is supposed to
replace default value.
Previously, when flag was set to `-flag=2` and the default value in
`NewDictInt` was set to 1 the resulting value for any `flag.Get()` call
would be 1 which is not expected.
This commit updates default value for the flag in case there is only one
entry for flag and the entry is a number without a key.
This affects cluster version and specifically `replicationFactor` flag
usage with vmstorage [node
groups](https://docs.victoriametrics.com/cluster-victoriametrics/#vmstorage-groups-at-vmselect).
Previously, the following configuration would effectively be ignored:
```
/path/to/vmselect \
-replicationFactor=2 \
-storageNode=g1/host1,g1/host2,g1/host3 \
-storageNode=g2/host4,g2/host5,g2/host6 \
-storageNode=g3/host7,g3/host8,g3/host9
```
Changes from this PR will force default value for `replicationFactor`
flag to be set to `2` which is expected as the result of this
configuration.
---------
Signed-off-by: Zakhar Bessarab <z.bessarab@victoriametrics.com>
1. Verify if field in [fields
pipe](https://docs.victoriametrics.com/victorialogs/logsql/#fields-pipe)
exists. If not, it generates a metric with illegal float value "" for
prometheus metrics protocol.
2. check if multiple time range filters produce conflicted query time
range, for instance:
```
query: _time: 5m | stats count(),
start:2024-10-08T10:00:00.806Z,
end: 2024-10-08T12:00:00.806Z,
time: 2024-10-10T10:02:59.806Z
```
must give no result due to invalid final time range.
---------
Co-authored-by: Aliaksandr Valialkin <valyala@victoriametrics.com>
It has been appeared that VictoriaLogs is frequently used for collecting logs with tens of fields.
For example, standard Kuberntes setup on top of Filebeat generates more than 20 fields per each log.
Such logs are also known as "wide events".
The previous storage format was optimized for logs with a few fields. When at least a single field
was referenced in the query, then the all the meta-information about all the log fields was unpacked
and parsed per each scanned block during the query. This could require a lot of additional disk IO
and CPU time when logs contain many fields. Resolve this issue by providing an (field -> metainfo_offset)
index per each field in every data block. This index allows reading and extracting only the needed
metainfo for fields used in the query. This index is stored in columnsHeaderIndexFilename ( columns_header_index.bin ).
This allows increasing performance for queries over wide events by 10x and more.
Another issue was that the data for bloom filters and field values across all the log fields except of _msg
was intermixed in two files - fieldBloomFilename ( field_bloom.bin ) and fieldValuesFilename ( field_values.bin ).
This could result in huge disk read IO overhead when some small field was referred in the query,
since the Operating System usually reads more data than requested. It reads the data from disk
in at least 4KiB blocks (usually the block size is much bigger in the range 64KiB - 512KiB).
So, if 512-byte bloom filter or values' block is read from the file, then the Operating System
reads up to 512KiB of data from disk, which results in 1000x disk read IO overhead. This overhead isn't visible
for recently accessed data, since this data is usually stored in RAM (aka Operating System page cache),
but this overhead may become very annoying when performing the query over large volumes of data
which isn't present in OS page cache.
The solution for this issue is to split bloom filters and field values across multiple shards.
This reduces the worst-case disk read IO overhead by at least Nx where N is the number of shards,
while the disk read IO overhead is completely removed in best case when the number of columns doesn't exceed N.
Currently the number of shards is 8 - see bloomValuesShardsCount . This solution increases
performance for queries over large volumes of newly ingested data by up to 1000x.
The new storage format is versioned as v1, while the old storage format is version as v0.
It is stored in the partHeader.FormatVersion.
Parts with the old storage format are converted into parts with the new storage format during background merge.
It is possible to force merge by querying /internal/force_merge HTTP endpoint - see https://docs.victoriametrics.com/victorialogs/#forced-merge .
After adding multitenant query feature at v1.104.0, searchQuery wasn't
properly unmarshalled at bottom vmselect in multi-level cluster setup.
It resulted into empty query responses.
This commit adds fallback to Unmarshal method of SearchQuery to fill
TenantTokens. It allows to properly execute search requests
at vmselect side.
Related issue:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7270
---------
Signed-off-by: f41gh7 <nik@victoriametrics.com>
Co-authored-by: Roman Khavronenko <roman@victoriametrics.com>
Empty fields are treated as non-existing fields by VictoriaLogs data model.
So there is no sense in returning empty fields in query results, since they may mislead and confuse users.
(cherry picked from commit bac193e50b)
s.partitions can be changed when new partition is registered or when old partition is dropped.
This could lead to data races and panics when s.partitions slice is accessed by concurrently executed queries.
The fix is to make a copy of the selected partitions under s.partitionsLock before performing the query.
(cherry picked from commit b4b79a4961)
This localizes blockSearch.getColumnsHeader() call at block_search.go .
This call is going to be optimized in the next commits in order to avoid
unmarshaling of header data for unneeded columns, which weren't requested
by getConstColumnValue() / getColumnHeader().
(cherry picked from commit 507b206a7d)
Refer the original byte slice with the marshaled columnsHeader for columns names and dictionary-encoded column values.
This improves query performance a bit when big number of blocks with big number of columns are scanned during the query.
(cherry picked from commit 279e25e7c8)
This should improve performance when blockSearch.getColumnsHeader() is called multiple times
from different places of the code.
(cherry picked from commit 9e48074b59)
br.bs may be nil when br contains the block with additional filters applied during pipe calculations.
For example, `* | count() if (error) errors`.
(cherry picked from commit 867f671cc4)
### Describe Your Changes
added opentelemetry exponential histograms support. Such histograms are automatically converted into
VictoriaMetrics histogram with `vmrange` buckets.
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: hagen1778 <roman@victoriametrics.com>
Co-authored-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit 9eb0c1fd86)
Improperly written pipes could be silently parsed as filter pipe.
For example, the following query:
* | by (x)
was silently parsed to:
* | filter "by" x
It is better to return error, so the user could identify and fix invalid pipe
instead of silently executing invalid query with `filter` pipe.
(cherry picked from commit 7b475ed95d)
### Describe Your Changes
Currently, vmagent always uses a separate `http.Client` for every group
watcher in Kubernetes SD. With a high number of group watchers this
leads to large amount of opened connections.
This PR adds 2 changes to address this:
- re-use of existing `http.Client` - in case `http.Client` is connecting
to the same API server and uses the same parameters it will be re-used
between group watchers
- HTTP2 support - this allows to reuse connections more efficiently due
to ability of using streaming via existing connections.
See this issue for the details and test results -
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/5971
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: Zakhar Bessarab <z.bessarab@victoriametrics.com>
Co-authored-by: Roman Khavronenko <roman@victoriametrics.com>
(cherry picked from commit eefae85450)
This PR fixes#7062
For hijacked connections, one has to read from the connection buffer,
but still write directly to the connection. Otherwise, when reading
directly from such connections, the first byte may be lost. This, in
turn corrupts the ClientHello TLS handshake message and when the backend
server receives it, it closes the connection and reports the following
error in the log:
```
http: TLS handshake error from 127.0.0.1:33150: tls: first record does not look
like a TLS handshake
```
The first byte may be lost because underlying HTTP request handler may
read it from the connection and put it into the buffer. As the result,
subsequent connection reads won't see that byte.
- See: https://github.com/golang/go/issues/27408
- The fix is taken from : https://github.com/k3s-io/k3s/pull/6216
### Checklist
The following checks are **mandatory**:
- [x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
Signed-off-by: Artem Fetishev <rtm@victoriametrics.com>
(cherry picked from commit c1cd3e85a7)
`vm_rows_ignored_total` metric is a metric for users to signalize about
ingestion issues, such as bad timestamp or parsing error.
In commit
a5424e95b3
this metric started to increment each time vmstorage gets NaN. But NaN
is a valid value for Prometheus data model and for Prometheus metrics
exposition format. Exporters from Prometheus ecosystem could expose NaNs
as values for metrics and these values will be delivered to vmstorage
and increment the metric.
Since there is nothing user can do with this, in opposite to parsing
errors or bad timestamps, there is not much sense in incrementing this
metric. So this commit rolls-back `reason="nan_value"` increments.
### Describe Your Changes
Please provide a brief description of the changes you made. Be as
specific as possible to help others understand the purpose and impact of
your modifications.
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
Signed-off-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit 0d4f4b8f7d)
Signed-off-by: hagen1778 <roman@victoriametrics.com>
### Describe Your Changes
Added an ability to query data across multiple tenants. See:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/1434
Currently, the following endpoints work with multi-tenancy:
- /prometheus/api/v1/query
- /prometheus/api/v1/query_range
- /prometheus/api/v1/series
- /prometheus/api/v1/labels
- /prometheus/api/v1/label/<label_name>/values
- /prometheus/api/v1/status/active_queries
- /prometheus/api/v1/status/top_queries
- /prometheus/api/v1/status/tsdb
- /prometheus/api/v1/export
- /prometheus/api/v1/export/csv
- /vmui
A note regarding VMUI: endpoints such as `active_queries` and
`top_queries` have been updated to indicate whether query was a
single-tenant or multi-tenant, but UI needs to be updated to display
this info.
cc: @Loori-R
---------
Signed-off-by: Zakhar Bessarab <z.bessarab@victoriametrics.com>
Signed-off-by: f41gh7 <nik@victoriametrics.com>
Co-authored-by: f41gh7 <nik@victoriametrics.com>
Create blockResultColumn.forEachDictValue* helper functions for visiting matching
dictionary values. These helper functions should prevent from counting dictionary values
without matching logs in the future.
This is a follow-up for 0c0f013a60
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7152
When ingesting samples with the same labels(duplicated samples or
samples with the same labels after `by` or `without` options). They
could register different entries for the same labelset in
LabelsCompressor.
For example, both index 99 and 100 can be assigned to label `foo=1` in
two concurrent pushes. Then due to differing label indexes in encoded
keys, the samples will appear as distinct in aggrState, resulting in
duplicated results after decompressing the label indexes.
fbde238cdc/lib/streamaggr/streamaggr.go (L933)
In this pull request, since we need to store `idxToLabel` first to
ensure the idx can be searched after `lc.labelToIdxStore`,
the `lc.idxToLabel` still could contain a duplicated entries
[100]="foo=1". But given the low likelihood of this issue and the size
of idxToLabel, it should be fine.
### Describe Your Changes
Introduce the `-search.maxDeleteSeries` flag that limits the number of
time series that can be deleted with a single
`/api/v1/admin/tsdb/delete_series` call.
Currently, any number can be deleted and if the number is big (millions)
then the operation may result in unaccounted CPU and memory usage spikes
which in some cases may result in OOM kill (see #7027). The flag limits
the number to 30k by default and the users may override it if needed at
the vmstorage start time.
Related issue:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7027
---------
Signed-off-by: Artem Fetishev <rtm@victoriametrics.com>
Previous commit 201fd6de1e removed
trailing space trim from data read from file. But common practice is to
remove such trailing space. And it leaded to the authorization errors
for the major group of users.
In first place, this change must help to mitigate an issue with
kubernetes. When authorization information was read from Secret content.
Changes to the operator was made to mitigate such problem at commit
1cf64358c8
We could introduce later optional flag for VictoriaMetrics to disable
trim space behavior.
Related issues:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6986https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7089https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6947
---------
Signed-off-by: f41gh7 <nik@victoriametrics.com>
Co-authored-by: Zhu Jiekun <jiekun@victoriametrics.com>
Previously the phrase filter with `!` was treated unexpectedly.
For example, `foo!bar` filter was treated at `foo AND NOT bar`,
while most users expect that it matches "foo!bar" phrase.
This commit aligns with users' expectations.
encoding.GetUint64s() returns uninitialized slice, which may contain arbitrary values.
So values in this slice must be reset to zero before using it for counting hits in `uniq` and `top` pipes.
This simplifies pipeProcessor initialization logic a bit.
This also doesn't mangle the original maxStateSize value, which is used in error messages when the state size exceeds maxStateSize.
This allows executing queries with `stats` pipe, which calculate multiple results with the same functions,
but with different `if (...)` conditions. For example:
_time:5m | count(), count() if (error)
Previously such queries couldn't be executed becasue automatically generated name for the second result
didn't include `if (error)`, so names for both results were identical - `count(*)`.
Now the following queries are equivalents:
_time:5s | sort by (_time)
_time:5s | order by (_time)
This is needed for convenience, since `order by` is commonly used in other query languages such as SQL.
Previously only logs inside the selected time range could be returned by stream_context pipe.
For example, the following query could return up to 10 surrounding logs only for the last 5 minutes,
while most users expect this query should return up to 10 surrounding logs without restrictions on the time range.
_time:5m panic | stream_context before 10
This enables the ability to implement stream context feature at VictoriaLogs web UI: https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7063 .
Reduce memory usage when returning stream context over big log streams with millions of entries.
The new logic scans over all the log messages for the selected log stream, while keeping in memory only
the given number of surrounding logs. Previously all the logs for the given log stream on the selected time range
were loaded in memory before selecting the needed surrounding logs.
This should help https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6730 .
Reduce the scan performance for big log streams by fetching only the requested fields. For example, the following
query should be executed much faster than before if logs contain many fields other than _stream, _msg and _time:
panic | stream_context after 30 | fields _stream, _msg, _time
Use local timezone of the host server in this case. The timezone can be overridden
with TZ environment variable if needed.
While at it, allow using whitespace instead of T as a delimiter between data and time
in the ingested _time field. For example, '2024-09-20 10:20:30' is now accepted
during data ingestion. This is valid ISO8601 format, which is used by some log shippers,
so it should be supported. This format is also known as SQL datetime format.
Also assume local time zone when time without timezone information is passed to querying APIs.
Previously such a time was parsed in UTC timezone. Add `Z` to the end of the time string
if the old behaviour is preferred.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6721
Previously the original timestamp was used in the copied query, so _time:duration filters
were applied to the original time range: (timestamp-duration ... timestamp]. This resulted
in stopped live tailing, since new logs have timestamps bigger than the original time range.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7028
This pipe is useful for debugging purposes when the number of processed blocks must be calculated for the given query:
<query> | blocks_count
This helps detecting the root cause of query performance slowdown in cases like https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7070
This improves performance for analytical queries, which do not need column headers metadata.
For example, the following query doesn't need column headers metadata, since _stream and min(_time)
are stored in block header, which is read separately from colum headers metadata:
_time:1w | stats by (_stream) min(_time) min_time
This commit significantly improves the performance for this query.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7070
Substitute global streamTagsCache with per-blockSearch cache for ((stream.id) -> (_stream value)) entries.
This improves scalability of obtaining _stream values on a machine with many CPU cores, since every CPU
has its own blockSearch instance.
This also should reduce memory usage when querying logs over big number of streams, since per-blockSearch
cache of ((stream.id) -> (_stream value)) entries is limited in size, and its lifetime is bounded by a single query.
The streamID.marshalString() is executed in hot path if the query selects _stream_id field.
Command to run the benchmark:
go test ./lib/logstorage/ -run=NONE -bench=BenchmarkStreamIDMarshalString -benchtime=5s
Results before the commit:
BenchmarkStreamIDMarshalString-16 438480714 14.04 ns/op 71.23 MB/s 0 B/op 0 allocs/op
Results after the commit:
BenchmarkStreamIDMarshalString-16 982459660 6.049 ns/op 165.30 MB/s 0 B/op 0 allocs/op
This test is very flaky and prevents other tests from running in CI.
Disabling this test should improve tests quality, since it isn't reliable anyway.
There is a ticket to fix this test - https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7062
Once fixed, this test should be uncommented.
Signed-off-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit c7569dac50)
### Describe Your Changes
It is better to show only unhealthy targets instead of all of them when
`show_only_unhealthy` filter is enabled.
Related issue:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/3536
### Checklist
The following checks are **mandatory**:
- [x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Co-authored-by: Roman Khavronenko <roman@victoriametrics.com>
(cherry picked from commit cbeb7d50e8)
Rounding GOMAXPROCS to the upper interger value of cpuQuota increases chances of CPU starvation,
non-optimimal goroutine scheduling and additional CPU overhead related to context switching.
So it is better to round GOMAXPROCS to the lower integer value of cpuQuota.
### Describe Your Changes
Currently it the metricID list is empty it won't be mashalled and as the
result won't be put into the tagFiltersToMetricIDsCache which causes the
cache misses for the corresponding tagFilters. In some setups this
causes severe search speed detradation (see #7009).
The empty metric IDs was covered before but then was accidentally
removed in 6c21439.
This PR restores the coverage of this case.
A new unit test can be used as a proof that empty metricID lists are not
added to the cache (just remove the fix in index_db.go and run the test
to see the result)
Also a benchmark has been added to see the implications of the
compression.
```
user@laptop:~/p/github.com/rtm0/VictoriaMetrics/01/src$ go test ./lib/storage/ -run=NONE -bench BenchmarkMarshalUnmarshalMetricIDs --loggerLevel=ERROR
goos: linux
goarch: amd64
pkg: github.com/VictoriaMetrics/VictoriaMetrics/lib/storage
cpu: 13th Gen Intel(R) Core(TM) i7-1355U
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-0-12 3237240 363.5 ns/op 0 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-1-12 2831049 451.8 ns/op 0.4706 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-10-12 1152764 1009 ns/op 1.667 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-100-12 297055 3998 ns/op 5.755 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-1000-12 31172 34566 ns/op 8.484 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-10000-12 4900 289659 ns/op 9.416 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-100000-12 447 2341173 ns/op 9.456 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-1000000-12 42 24926928 ns/op 9.468 compression-rate
BenchmarkMarshalUnmarshalMetricIDs/numMetricIDs-10000000-12 5 204098872 ns/op 9.467 compression-rate
PASS
ok github.com/VictoriaMetrics/VictoriaMetrics/lib/storage 15.018s
```
### Checklist
The following checks are **mandatory**:
- [x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
Co-authored-by: Aliaksandr Valialkin <valyala@victoriametrics.com>
The indexSearch.containsTimeRange() function is called for the current indexDB and the previous indexDB
every time when searching for metricIDs by label filters. This function consumes a lot of additional CPU time
for cases when queries with lightweight label filters are sent to VictoriaMetrics at high rate (e.g. thousands of RPS),
like in the issue https://github.com/VictoriaMetrics/VictoriaMetrics/issues/7009 .
Optimize indexSearch.containsTimeRange() function in the following ways:
- Unconditionally return true if this function is called for the current indexDB, since there are very high
chances that the current indexDB contains the data with timestamps in the requested time range.
- Cache the minimum timestamp, which is missing in the indexed data for the previous indexDB.
This is safe to do, since the previous indexDB is readonly.
This optimization eliminates potentially slow lookup in the previous indexDB for typical
use cases when the requested time range is close to the current time.
Previously indexDB.doExtDB() was returning boolean value, which was indicating whether f callback was called.
There is no need in returning this boolean value, since the f callback can determine on itself whether it was called.
This simplifies the code a bit.
While at it, document indexDB.doExtDB().
Make function name and comments more clear.
d8f8822fa5
Signed-off-by: hagen1778 <roman@victoriametrics.com>
Co-authored-by: Nikolay <nik@victoriametrics.com>
This fixes flaky test TestGetCommonTokensForOrFilters:
filter_or_test.go:143: unexpected tokens for field "_msg"; got ["foo" "bar"]; want ["bar" "foo"]
…g from 1e3 to 5e3
This should improve visibility on errors produced by very long queries.
The change is classified as BUG in order to port it to LTS releases.
### Describe Your Changes
Please provide a brief description of the changes you made. Be as
specific as possible to help others understand the purpose and impact of
your modifications.
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: hagen1778 <roman@victoriametrics.com>
Co-authored-by: Mathias Palmersheim <mathias@victoriametrics.com>
(cherry picked from commit e115b85770)
* Previously, only metricID->metricName missing index records were
tracked with deadline But it was possible a case for missing
metricID->TSID index records. IndexDB metrics fix exposed misleading
metric for such missing records.
* This commit adds check for metricID->TSID missing index records. And
delete missing metricID entry if it hit 60 second deadline.
Related issue
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6931
Signed-off-by: f41gh7 <nik@victoriametrics.com>
Previously we manually imported system windows DDLs
and made direct syscall.
But golang exposes syscall wrappers with sys/windows package.
It seems, that direct syscall was broken at 1.23 golang release. It was
`GetDiskFreeSpace` syscall in our case.
This commit replaces all manual syscalls with wrappers
Related issue:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6973
Related golang issue:
https://github.com/golang/go/issues/69029
Signed-off-by: f41gh7 <nik@victoriametrics.com>
Previously the query could return incorrect results, since the query timestamp was updated with every Query.Clone() call
during iterative search for the time range with up to limit=N rows.
While at it, optimize queries, which find low number of matching logs, while spend a lot of CPU time for searching
across big number of logs. The optimization reduces the upper bound of the time range to search if the current time range
contains zero matching rows.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6785
Previously tokens from AND filters were extracted in random order. This could slow down
checking them agains bloom filters if the most specific tokens go at the beginning of the AND filters.
Preserve the original order of tokens when matching them against bloom filters,
so the user could control the performance of the query by putting the most specific AND filters
at the beginning of the query.
While at it, add tests for getCommonTokensForAndFilters() and getCommonTokensForOrFilters().
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6554
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/pull/6556
Previously the following query could miss rows matching !bar if these rows do not contain foo:
foo OR !bar
This is because of incorrect detection of common tokens for OR filters - all the unsupported filters
were skipped (including the NOT filter (aka `!`)), while in this case zero common tokens must be returned.
While at it, move repetiteve code in TestFilterAnd and TestFilterOr into f function.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6554
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/pull/6556
This is needed for avoiding confusion between the `|` operator at `math` pipe and `|` pipe delimiter.
For example, the following query was parsed unexpectedly:
* | math foo / bar | fields x
as
* | math foo / (bar | fields) as x
Substituting `|` with `or` inside `math` pipe fixes this ambiguity.
### Describe Your Changes
Add storage metrics that count records that failed to insert:
- `RowsReceivedTotal`: the number of records that have been received by
the storage from the clients
- `RowsAddedTotal`: the number of records that have actually been
persisted. This value must be equal to `RowsReceivedTotal` if all the
records have been valid ones. But it will be smaller otherwise. The
values of the metrics below should provide the insight of why some
records hasn't been added
- `NaNValueRows`: the number of records whose value was `NaN`
- `StaleNaNValueRows`: the number of records whose value was `Stale NaN`
- `InvalidRawMetricNames`: the number of records whose raw metric name
has failed to unmarshal.
The following metrics existed before this PR and are listed here for
completeness:
- `TooSmallTimestampRows`: the number of records whose timestamp is
negative or is older than retention period
- `TooBigTimestampRows`: the number of records whose timestamp is too
far in the future.
- `HourlySeriesLimitRowsDropped`: the number of records that have not
been added because the hourly series limit has been exceeded.
- `DailySeriesLimitRowsDropped`: the number of records that have not
been added because the daily series limit has been exceeded.
---
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
Previously per-token hashes for per-block bloom filters were re-calculated on every scanned block.
This could be slow when the number of tokens is big or when the number of blocks to scan is big.
Pre-calculate hashes for bloom filters and then use them for searching in bloom filters.
This improves performance by 2.5x for in(...) filters with many values to search inside `in()`.
Previous bugfix at 49f63b2 only partially fixed pagination host validation error.
Before this fix it was:
```
unexpected nextLink host \"management.azure.com\", expecting \"https://management.azure.com\"
```
Now we only check the `Host` without schema.
However, when Azure respond `nextLink` in `Host:Port` format, the
`nextLink` check will fail:
```
unexpected nextLink host \"management.azure.com:443\", expecting \"management.azure.com\"
```
This pull request further relaxes the checks by only checking the
`Hostname`.
---
related issue: https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6912
This patch reverts 1fd3385
After discussing it we've come to conclusion that this is a valid
behavior which can be avoided by deleting the time series only once the
corresponding stale NaNs have been received.
On the other hand, the fix leads to lost stale NaNs in some rare but
valid use cases. For example:
- In a cluster configuration the samples for a given time series are
normally sent to the same vmstorage replica. However, wminsert may
reroute the samples to another replica because the original one is down
or is overloaded. In this case the stale NaN may end up on a replica
that has no data for that time series, but we still want to record that
sample.
Thus, reverting that fix.
---
related issue https://github.com/VictoriaMetrics/VictoriaMetrics/issues/5069
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
follow up
4ecc370acb
### Describe Your Changes
Please provide a brief description of the changes you made. Be as
specific as possible to help others understand the purpose and impact of
your modifications.
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
Previously (f1:foo OR f2:bar) was incorrectly returning `foo` token for `f1` and `bar` token for `f2`.
These tokens were used for checking against bloom filter for every data block, so the data block,
which didn't contain simultaneously `foo` token for `f1` field and `bar` token for `f2` field, was skipped.
This was incorrect, since such a block may contain logs matching the original OR filter.
The fix is to return common tokens from `OR`-delimted filters only if these tokens exist at EVERY such filter
for the given field name. If some `OR`-delimited filter misses the given field name, then `OR`-delimited filters
do not contain common tokens, which could be used for checking against bloom filter.
While at it, add more tests covering various edge cases for filters delimited by AND and OR.
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6554
Updates https://github.com/VictoriaMetrics/VictoriaMetrics/pull/6556
Commit adds the following changes:
* Adds support of OpenTelemetry logs for Victoria Logs with protobuf encoded messages
* json encoding is not supported for the following reasons:
- It brings a lot of fragile code, which works inefficiently.
- json encoding is impossible to use with language SDK.
* splits metrics and logs structures at lib/protoparser/opentelemetry/pb package.
* adds docs with examples for opentelemetry logs.
---
Related issue: https://github.com/VictoriaMetrics/VictoriaMetrics/issues/4839
Co-authored-by: AndrewChubatiuk <andrew.chubatiuk@gmail.com>
Co-authored-by: f41gh7 <nik@victoriametrics.com>
fix#6554
andfilter shouldn't return orfilter field which result in bloomfilter
return false.
---------
Co-authored-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit 975ed27a76)
### Describe Your Changes
This is a follow-up PR: Unit tests introduced in #6872 can now use
RowsAddedTotal counter whose scope was fixed in #6841.
### Checklist
The following checks are **mandatory**:
- [x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
Co-authored-by: Nikolay <nik@victoriametrics.com>
(cherry picked from commit 2c856c6951)
### Describe Your Changes
fsync() ensures that the data is written to disk. In production this is
needed for data durability. However, during the development, when the
unit tests are run, this level of durability is not needed. Therefore
fsync() can be disabled which will makes test runs two times faster.
The disabling is done by setting the `DISABLE_FSYNC_FOR_TESTING`
environment variable. The valid values for this variable are the same as
the values of the arg of `go doc strconv.ParseBool`:
```
1, t, T, TRUE, true, True, 0, f, F, FALSE, false, False.
```
Any other value means `false`.
The variable is set for all test build targets. Compare running times:
Build Target | DISABLE_FSYNC_FOR_TESTING=0 | DISABLE_FSYNC_FOR_TESTING=1
----------------- | ------------------------------------------------ |
-------------------------------------------------
make test | 1m5s | 0m22s
make test-race | 3m1s | 1m42s
make test-pure | 1m7s | 0m20s
make test-full | 1m21s | 0m32s
make test-full-386 | 1m42s | 0m36s
When running tests for a given package, fsync can be disabled as
follows:
```shell
DISABLE_FSYNC_FOR_TESTING=1 go test ./lib/storage
```
Disabling fsync() is intended for testing purposes only and the name of
the variables reflects that.
What could also have been done but haven't:
- lib/filestream/filestream.go: `Writer.MustFlush()` also uses f.Sync()
but nothing has been done to it, because the Writer.MustFlush() is not
used anywhere in the VM codebase. A side question: what is the general
policy for the unused code?
- lib/filestream/filestream.go: Writer.Write() calls `adviceDontNeed()`
which calls unix.Fdatasync(). Disabling it could potentially improve
running time, but running tests with this code disabled has shown
otherwise.
### Checklist
The following checks are **mandatory**:
- [ x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
(cherry picked from commit 334cd92a6c)
Signed-off-by: hagen1778 <roman@victoriametrics.com>
Previously, some extIndexDB metrics were not registered. It resulted
into missing metrics, if metric value was added to the extIndexDB. It's
a usual case for search requests at both indexes.
Current commit updates all metrics from extIndexDB according to the
current IndexDB. It must fix such cases
Related issue:
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6868
### Describe Your Changes
Please provide a brief description of the changes you made. Be as
specific as possible to help others understand the purpose and impact of
your modifications.
### Checklist
The following checks are **mandatory**:
- [ ] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
(cherry picked from commit 4ecc370acb)
`TL;DR` This PR improves the metric IDs search in IndexDB:
- Avoid seaching for metric IDs twice when `maxMetrics` limit is
exceeded
- Use correct error type for indicating that the `maxMetrics` limit is
exceded
- Simplify the logic of deciding between per-day and global index search
A unit test has been added to ensure that this refactoring does not
break anything.
---
Function calls before the fix:
```
idb.searchMetricIDs
|__ is.searchMetricIDs
|__ is.searchMetricIDsInternal
|__ is.updateMetricIDsForTagFilters
|__ is.tryUpdatingMetricIDsForDateRange
| |
|__ is.getMetricIDsForDateAndFilters
```
- `searchMetricIDsInternal` searches metric IDs for each filter set. It
maintains a metric ID set variable which is updated every time the
`updateMetricIDsForTagFilters` function is called. After each successful
call, the function checks the length of the updated metric ID set and if
it is greater than `maxMetrics`, the function returns `too many
timeseries` error.
- `updateMetricIDsForTagFilters` uses either per-day or global index to
search metric IDs for the given filter set. The decision of which index
to use is made is made within the `tryUpdatingMetricIDsForDateRange`
function and if it returns `fallback to global search` error then the
function uses global index by calling `getMetricIDsForDateAndFilters`
with zero date.
- `tryUpdatingMetricIDsForDateRange` first checks if the given time
range is larger than 40 days and if so returns `fallback to global
search` error. Otherwise it proceeds to searching for metric IDs within
that time range by calling `getMetricIDsForDateAndFilters` for each
date.
- `getMetricIDsForDateAndFilters` searches for metric IDs for the given
date and returns `fallback to global search` error if the number of
found metric IDs is greater than `maxMetrics`.
Problems with this solution:
1. The `fallback to global search` error returned by
`getMetricIDsForDateAndFilters` in case when maxMetrics is exceeded is
misleading.
2. If `tryUpdatingMetricIDsForDateRange` proceeds to date range search
and returns `fallback to global search` error (because
`getMetricIDsForDateAndFilters` returns it) then this will trigger
global search in `updateMetricIDsForTagFilters`. However the global
search uses the same maxMetrics value which means this search is
destined to fail too. I.e. the same search is performed twice and fails
twice.
3. `too many timeseries` error is already handled in
`searchMetricIDsInternal` and therefore handing this error in
`updateMetricIDsForTagFilters` is redundant
4. updateMetricIDsForTagFilters is a better place to make a decision on
whether to use per-day or global index.
Solution:
1. Use a dedicated error for `too many timeseries` case
2. Handle `too many timeseries` error in `searchMetricIDsInternal` only
3. Move the per-day or global search decision from
`tryUpdatingMetricIDsForDateRange` to `updateMetricIDsForTagFilters` and
remove `fallback to global search` error.
---------
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
Co-authored-by: Nikolay <nik@victoriametrics.com>
Once the timeseries is in tsidCache, new entries won't be created in
per-day index because the RegisterMetricNames() code does consider
different dates for the same timeseries. So this case has been added.
The same bug exists for AddRows() but it is not manifested because the
index entries are finally created in updatePerDateData().
RegisterMetricNames also updated to increase the newTimeseriesCreated
counter because it actually creates new time series in index.
A unit tests has been added that check all possible data patterns
(different metric names and dates) and code branches in both
RegisterMetricNames and AddRows. The total number of new unit tests is
around 100 which increaded the running time of storage tests by 50%.
---------
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
Co-authored-by: Roman Khavronenko <hagen1778@gmail.com>
### Describe Your Changes
Reduced the scope of rowsAddedTotal variable from global to Storage.
This metric clearly belongs to a given Storage object as it counts the
number of records added by a given Storage instance.
Reducing the scope improves the incapsulation and allows to reset this
variable during the unit tests (i.e. every time a new Storage object is
created by a test, that object gets a new variable).
Signed-off-by: Artem Fetishev <wwctrsrx@gmail.com>
In the previous commit 8958cecad6
the default ports (80/443) were removed for both the `scrapeURL` and
`instance` label values for those targets without a port in
`__address__`. Different values in the `instance` label generate new
time series.
This commit reverts the changes made to the `instance` label. Now,
for those targets:
- `scrapeURL` will remain unchanged.
- The `instance` label value will include the default port.
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6792
(cherry picked from commit e97e966f82)
* Adds custom dial func for HTTP-Connect and socks5 proxy tunnels.
Standard golang http.transport exposes GetProxyConnectHeader function,
but it doesn't allow to use separate tls config for proxy.
It also not possible to enforce HTTP-Connect with standard http lib.
* For http scrape targets, by default http.Transport.Proxy function must
be used. Since it has special case with full uri forward.
* Adds proxy.URL json methods that allow to properly copy internal
fields, like User/Password.
It should fix bug with proxy_url. When credentials specified at URL was
ignored.
* Adds tests for scrape client proxy requests
related issue https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6771
* It was necessary to add default ports for fasthttp client. After migration to the std.httpclient it's no longer needed.
* An additional configuration is required at proxy servers with implicitly set 80/443 ports to the host header (such as HA proxy.
It's expected that after upgrade __address_ label may change. But it should be rare case. 80/443 ports are not widely used at monitoring ecosystem. And it shouldn't have much impact.
Related issue https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6792
Co-authored-by: Nikolay <nik@victoriametrics.com>
…eep_metric_names` options in stream aggregation config together
With aggregated data and raw data under the same metric, results would
be confusing.
---------
Signed-off-by: hagen1778 <roman@victoriametrics.com>
Co-authored-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit 62d19369a3)
### Describe Your Changes
This helps to improve reliability of performing backups in environments
with unreliable connection and tolerate temporary errors at S3 provider
side.
See: https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6732
Default retry timeout is up to 3 minutes to make this consistent with
the same configuration for GCS:
a05317f61f/lib/backup/gcsremote/gcs.go (L70-L76)
### Checklist
The following checks are **mandatory**:
- [x] My change adheres [VictoriaMetrics contributing
guidelines](https://docs.victoriametrics.com/contributing/).
---------
Signed-off-by: Zakhar Bessarab <z.bessarab@victoriametrics.com>
(cherry picked from commit cb00b4b00f)
Before, buffer growth was always x2 of its size, which could lead to
excessive memory usage when processing big amount of data.
For example, scraping a target with hundreds of MBs in response could
result into hih memory spikes in vmagent because buffer has to double
its size to fit the response. See
https://github.com/VictoriaMetrics/VictoriaMetrics/issues/6759
The change smoothes out the growth rate, trading higher allocation rate
for lower mem usage at certain conditions.
---------
Signed-off-by: hagen1778 <roman@victoriametrics.com>
(cherry picked from commit f28f496a9d)
