docu: test results on Alpitronics

doc/bug_analysis.md

@@ -1,22 +1,30 @@
 # Open issues
 
+## Issue16: First CurrentDemandReq is rejected with FAILED_SequenceError and EVSE_Shutdown
+- observed on Alpitronics HPC with version v0.4-6-g257e5af
+- log 2022-12-20_alpi_currentDemandSequenceErrorShutdown.pcapng
+- same result in two trys
+
 ## Issue15: After end of PreCharging, the log says "re-initializing fsmPev"
 - observed with v0.4 on the Compleo charger
 - PreCharge target voltage is reached. The fsmPev sends a message
 01fe800100000012809a022189cbf75b9625a9513022800a0800
 and after one second the state machine seems to run into timeout.
 
-## Issue14: Connection loss after authorization
+
+# Closed issues
+
+## [Solved] Issue14: Connection loss after authorization
 - with version v0.4.
 - same version works fine on Compleo
 - could be also caused by weak power of the powerbank. The TpLink and Dieter made restart from time to time.
 - to be retested with better supply and on other chargers.
+- Test pass with v0.4-6-g257e5af, with the Intenso two-cell powerbank.
 
-## Issue12: Alpi reports "sequence error" for CableCheck
+## [Solved] Issue12: Alpi reports "sequence error" for CableCheck
 - with version v0.3.
 - maybe he expects the state C, or something is wrong with the sequence before.
-
-# Closed issues
+- Test pass with v0.4-6-g257e5af
 
 ## [Solved] Issue13: Compleo SLAC stops after SlacParamResponse
 - Root cause: The Compleo ignores the StartAttenChar, if the timeout field is set to 1000ms instead of the nominal 600ms.

doc/charger_test_results.md

@@ -27,7 +27,7 @@ Test results tbd
 
 Test site: e.g. https://www.goingelectric.de/stromtankstellen/Deutschland/Ingolstadt/Dehner-Garten-Center-Degenhartstrasse-Degenhartstrasse-2/71112/
 
-Test results of version v0.3
+Test results of version v0.4-6-g257e5af
 - [x] SLAC
 - [x] SDP
 - [x] TCP connection
@@ -35,11 +35,17 @@ Test results of version v0.3
     - [x] DIN SupportedApplicationProtocol
 	- [x] DIN SessionSetup
 	- [x] DIN ServiceDiscovery
-	- [x] DIN ChargeParameterDiscovery
+	- [x] DIN ServicePaymentSelection
 	- [x] DIN ContractAuthentication
-	- [ ] DIN CableCheck
-	- [ ] DIN PreCharge
-	- [ ] DIN PowerDelivery, CurrentDemand
+	- [x] DIN ChargeParameterDiscovery
+	- [x] DIN CableCheck
+	- [x] DIN PreCharge
+	- [x] DIN PowerDelivery Start
+	- [ ] DIN CurrentDemand rejected with FAILED_SequenceError and EVSE_Shutdown. Issue 16
+	- [ ] DIN PowerDelivery Stop
+	- [ ] DIN WeldingDetection
+	- [ ] DIN SessionStop
+- [x] Inlet voltage measurement (shows 500V during cable check, and 230V during precharge)
 
 ## Compleo Cito BM 500
 

readme.md

@@ -299,6 +299,12 @@ is not yet implemented.
 - PreCharge starts, but terminates before full voltage is reached. Switching the load with power-relay is not yet implemented from
 hardware side. Without the load, we see the intended 230V precharge voltage, and run into timeout (to be investigated).
 
+### 2022-12-20 Measurement of inlet voltage works
+- Tests ran on Alpitronics HPC.
+- Measuring the inlet voltage with Arduino "Dieter" works. During CableCheck and PreCharge, the inlet voltage is shown in the GUI.
+- The Alpi confirms the PowerDelivery (start), but rejects the CurrentDemandRequest with FAILED_SequenceError and EVSE_Shutdown.
+- Results (log file and pcap) are stored in https://github.com/uhi22/pyPLC/tree/master/results.
+
 ### Test results on real-world chargers
 
 See [charger_test_results.md](doc/charger_test_results.md)